Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Enhanced softening resistance and mechanical properties of Mo 2 C particle-reinforced Cu-matrix composites

Enhanced Softening Resistance and Mechanical Properties of Mo2C Particle-Reinforced Cu-matrix Composites

Mo2C particle-reinforced CuCrZr composite with enhanced wear and softening resistance

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Microstructure Evolution and Properties of a Cu-5 Wt.% Mo Alloy with High Conductivity and High Anti-Soften Temperature

Microstructure and Mechanical Properties of High Densification Mo/Cu Composites

Preparation and Properties Study of Cu-MoSi<sub>2</sub> Composites

Effect of Mo Nanoparticles on Microstructure and Mechanical Properties of Cu Alloys by Self-Propagating and Spark Plasma Sintering

Influence of Preparation Temperature of Mo2C Interlayer on Microstructure and Properties of C/C-Cu Composites

Simultaneous improvement of microstructure and high-temperature tensile properties in CNT-doped Mo-based composites

Microstructures and Properties of Cu/50 Vol.% MoS2 Composites Prepared with Cu-coated MoS2 Powders and Sintered at Different Temperatures

Microstructure and thermal and electric conductivities of high dense Mo/Cu composites

Sintering Behavior and Properties of Mo-Cu Composites

Effect of Graphitization on the Microstructure and Properties of Mo2C‐Modified C/C–Cu Composites

Improving the mechanical properties and coefficient of thermal expansion of molybdenum-reinforced copper using powder metallurgy

Microscopic Formation Mechanism and Physical Properties of Mo/Cu Composites with High Densification

Preparation of a C/C–Cu Composite with Mo2C Coatings As a Modification Interlayer

On effect of particle size distribution on the elastic/plastic deformation of metal matrix composites

Cyclic warm rolling: A path to superior properties in Mo Cu composites

In Situ Fabrication and Static Contact Resistance of CdMoO4 Reinforced Cu Matrix Composites

Interface and Mechanical/thermal Properties of Graphene/copper Composite with Mo2C Nanoparticles Grown on Graphene