Abstract:Multi-walled carbon nanotubes (MWCNTs) are one of the ideal reinforcements for metal matrix composites (MMCs), however, it faced a big challenge regarding their mechanical compatibility of MWCNTs reinforced titanium matrix composites (TMCs) due to its strong agglomeration, undesirable interfacial reaction and etc. To overcome this key problem, we employed Cu nanoparticles to decorate MWCNTs (Cu-MWCNTs) and successfully fabricated Cu-MWCNTs reinforced TMCs with the support of hot-pressed sintering (HPS) approach. The addition of Cu nanoparticles not only improved its dispersion, but also effectively reduced the interfacial reaction through the in-situ synthesized interfacial Ti2Cu phases and preserving the integrity of MWCNTs. Tensile studies reflected that the addition of 0.5 wt % Cu-MWCNTs was advantageous in improving the tensile properties, breaking through the trade-off between the strength and ductility, which were 15% and 45% higher than the matrix alloy, respectively. The quantitatively analysis of the increased strength proved that the primary strengthening mechanisms included the grain refinement, the solid solution of the carbon atoms from MWCNTs and the efficient load transfer from the multiple interfaces with in-situ synthesized interfacial Ti2Cu phases. The improvement in toughness was mainly derived from the high dislocation storage capacity induced by interfacial modification, thus achieving the higher uniform elongation in TMCs. Consequently, this work provided the promising approach to design strong and ductile TMCs.

Simultaneous improvement of microstructure and high-temperature tensile properties in CNT-doped Mo-based composites

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites

Investigation of Microstructure and Strengthening Mechanism in CNTs Reinforced Mo-based Composites

Microstructural Evolution and Mechanical Properties of Carbon Nanotubes–reinforced TZM Composites Synthesized by Powder Metallurgy

Microstructures and Enhanced Flexural Properties of Single-Crystalline HfC Nanowires In-Situ Modified Carbon/carbon Composites by Electrophoresis-Thermal Evaporation Using CNTs As the Template

Simultaneously Enhancing Strength and Ductility of Carbon Nanotube/Aluminum Composites by Improving Bonding Conditions

Microstructure and Properties of MoSi 2 Intermetallic Reinforced and Toughening by Carbon Nanotube

Enhanced softening resistance and mechanical properties of Mo 2 C particle-reinforced Cu-matrix composites

Preparation and properties of HfB2-HfC and HfB2-HfC-MoB composites by reactive spark plasma sintering

MoSi2 Inter-Metallic Composites Reinforced and Toughened by CNTs

Effect of carbon on microstructure and high-temperature strength of NbMoTiSi in situ composites prepared by arc-melting and directional solidification

CNTs/Cu-Ti Composites Fabrication Through the Synergistic Reinforcement of CNTs and in Situ Generated Nano-Tic Particles

Sintering Behavior and Properties of Mo-Cu Composites

Interfacial modification strategy to break through the strength and ductility trade-off in multi-walled carbon nanotubes reinforced titanium matrix composites

Preparation and elevated temperature compressive properties of multi-walled carbon nanotube reinforced Ti composites

Enhanced Softening Resistance and Mechanical Properties of Mo2C Particle-Reinforced Cu-matrix Composites

Multiwalled Carbon Nanotubes–TiB2–Ni Composite: Microstructure and Mechanical Properties

Preparation and In-Situ Strengthening Mechanisms of Mo Composites with the Addition of WC

Architectural and component design of CNTs/Al hierarchical composite for enhanced mechanical/thermal properties

Regulating the Mechanical Properties of (μm B4C+nm SiC)/7075Al Composites Via Nano-Sic Content

Sintering And Enhanced Mechanical Properties Of Densified Multiwalled Carbon Nanotube/Tin Composites