Abstract:To improve the strength and toughness of Mg matrix composites, we propose a novel strategy to successfully develop Mg matrix composites reinforced with alternating fiber-like nanoparticle-rich (NPR) zones. A combination of in-situ casting and hot thermomechanical processing approach is employed to achieve this unique microstructure, and the influence of spatial arrangement of TiB2 nanoparticles on the microstructure, mechanical behavior, strengthening and toughening mechanisms are investigated in detail. The results show that the designed nanocomposite exhibits alternative fiber-like NPR zones and nanoparticle-free (NPF) zones, leading to the typical bimodal structure. Meanwhile, EBSD analyses reveal that the fiber-like NPR zones have much higher density of geometrically necessary dislocations than NPF zones. Accordingly, the hardness and elastic modulus in fiber-like NPR zones are enhanced significantly, acting as "hard" units, while NPF zones with high plasticity factor acting as "soft" regions. As a consequence, superior combination of tensile strength (388 MPa) and ductility (10.1%) is realized in TiB2/AZ91 nanocomposite when compared to AZ91 matrix. The strengthening mechanisms of the nanocomposite are evaluated quantitatively, and found that the fiber-like arrays significantly enhanced the load-bearing capacity of TiB2 nanoparticles. Moreover, grains in NPF zones can deform easily, acting as strain bearing soft units, coupling with cracks deflection caused by the "hard" NPR zones, both of which are responsible for toughening nanocomposite.

Combination of enhanced thermal conductivity and strength of MWCNTs reinforced Mg-6Zn matrix composite

Enhancement of thermal–mechanical performances via a selective CNTs configuration in laminated CNTs/AZ31B composite

Mechanical and Conductive Properties of Cu Matrix Composites Reinforced by Oriented Carbon Nanotubes with Different Coatings

Simultaneous achievement of high electromagnetic shielding effectiveness (X-band) and strength in Mg-Li-Zn-Gd/MWCNTs composite

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

Strengthening and toughening mechanisms of CNTs/Mg–Al composites prepared via powder metallurgy combined with hot extrusion

Mechanical properties and fabrication of carbon nanotubes reinforced AZ91D magnesium matrix nanocomposites

An improved approach to manufacture CNT reinforced magnesium AZ91 composites with increased strength and ductility

Strengthening Ni-Coated CNT/Mg Composites by Optimizing the CNT Content

Enhanced ductility by Mg addition in the CNT/Al-Cu composites via flake powder metallurgy

Developing Fittingly Comprehensive Performance Carbon Nanotube/Mg-6Zn Sheets with Substantial Enhancement in Formability

Simultaneous improvement of microstructure and high-temperature tensile properties in CNT-doped Mo-based composites

Synergistic Strengthening of Mechanical Properties and Electromagnetic Interference Shielding Performance of Carbon Nanotubes (CNTs) Reinforced Magnesium Matrix Composites by CNTs Induced Laminated Structure

Influence of Soft Phase and Carbon Nanotube Content on the Properties of Hierarchical AZ61 Matrix Composite with Isolated Soft Phase

Effect of heat treatment on the microstructure, mechanical properties and fracture behaviors of ultra-high-strength SiC/Al–Zn–Mg–Cu composites

Study on Microstructure and Mechanical Properties of TC4/AZ31 Magnesium Matrix Nanocomposites

The Microstructure and Mechanical Properties of Carbon Nanotube-Reinforced W-Matrix Composites

Fabrication and Characterization of PMMA/MWCNTs Composite Materials

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes

Plastic deformation mechanism of MWCNTs/AZ91D nanocomposites with high ductility at room temperature

Strengthening and Toughening Mechanisms of Mg Matrix Composites Reinforced with Specific Spatial Arrangement of In-Situ TiB2 Nanoparticles