Abstract:Multi-walled carbon nanotubes (MWCNTs) are one of the ideal reinforcements for metal matrix composites (MMCs), however, it faced a big challenge regarding their mechanical compatibility of MWCNTs reinforced titanium matrix composites (TMCs) due to its strong agglomeration, undesirable interfacial reaction and etc. To overcome this key problem, we employed Cu nanoparticles to decorate MWCNTs (Cu-MWCNTs) and successfully fabricated Cu-MWCNTs reinforced TMCs with the support of hot-pressed sintering (HPS) approach. The addition of Cu nanoparticles not only improved its dispersion, but also effectively reduced the interfacial reaction through the in-situ synthesized interfacial Ti2Cu phases and preserving the integrity of MWCNTs. Tensile studies reflected that the addition of 0.5 wt % Cu-MWCNTs was advantageous in improving the tensile properties, breaking through the trade-off between the strength and ductility, which were 15% and 45% higher than the matrix alloy, respectively. The quantitatively analysis of the increased strength proved that the primary strengthening mechanisms included the grain refinement, the solid solution of the carbon atoms from MWCNTs and the efficient load transfer from the multiple interfaces with in-situ synthesized interfacial Ti2Cu phases. The improvement in toughness was mainly derived from the high dislocation storage capacity induced by interfacial modification, thus achieving the higher uniform elongation in TMCs. Consequently, this work provided the promising approach to design strong and ductile TMCs.

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites

Simultaneous improvement of microstructure and high-temperature tensile properties in CNT-doped Mo-based composites

Investigation of Microstructure and Strengthening Mechanism in CNTs Reinforced Mo-based Composites

Wet Powder Metallurgy Process for Dispersing Carbon Nanotubes and Fabricating Magnesium Composite

Microstructural Evolution and Mechanical Properties of Carbon Nanotubes–reinforced TZM Composites Synthesized by Powder Metallurgy

Design of an Efficient Flake Powder Metallurgy Route to Fabricate CNT/6061Al Composites

A New Technique for Dispersion of Carbon Nanotube in A Metal Melt

A Novel Method to Fabricate CNT/Mg–6Zn Composites with High Strengthening Efficiency

Aluminum Matrix Composites Reinforced by Molybdenum-Coated Carbon Nanotubes

Interfacial modification strategy to break through the strength and ductility trade-off in multi-walled carbon nanotubes reinforced titanium matrix composites

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites

Development and Strengthening Mechanisms of a Hybrid CNTs@SiCp/Mg-6Zn Composite Fabricated by a Novel Method

Enhancing Interfacial Bonding And Tensile Strength In Cnt-Cu Composites By A Synergetic Method Of Spraying Pyrolysis And Flake Powder Metallurgy

Modifying the Properties of Tungsten Based Plasma Facing Materials with Single-Wall Carbon Nanotubes

Fabrication of Copper Matrix Composites Reinforced with Carbon Nanotubes Using an Innovational Self-Reduction Molecular-Level-Mixing Method

Enhanced Interfacial Bonding and Mechanical Properties in CNT/Al Composites Fabricated by Flake Powder Metallurgy

Interfacial/intragranular reinforcement of titanium-matrix composites produced by a novel process involving core-shell structured powder

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Microstructures and Enhanced Flexural Properties of Single-Crystalline HfC Nanowires In-Situ Modified Carbon/carbon Composites by Electrophoresis-Thermal Evaporation Using CNTs As the Template

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Enhanced properties of carbon nanotube-graphite hybrid-reinforced Cu matrix composites via optimization of the preparation technology and interface structure