Abstract:Cu/Al composites have the excellent properties of both Cu and Al, and have the properties of light weight and high conductivity, so they have been widely concerned. In this paper, 5-mm-thick Cu/Al composites prepared by the cast-rolling process are used as experimental materials. To reveal the strengthening and toughening mechanisms of the Cu/Al composites, the interfacial structure, micro-morphology, stress-strain condition, and GND distribution of Cu/Al composites before and after deformation were characterized utilizing TEM, TKD, and EBSD. The results show that the submicron intermetallic compounds Al 2 Cu and Al 4 Cu 9 are formed from the casting-rolling Cu/Al composites. After 15% tensile deformation, many gaps occurred in the interface layer, but at the gaps, there was no crack spreading to the Cu and Al layers. Meanwhile, the deformation in different directions occurs in the Cu grains near the interface, forming a dislocation wall, and the entanglement of the dislocation occurs in the Cu layer near the interface, which contributes to the improvement of tensile strength. The Al layer near the interface layer produces kink bands, which helps to improve the ductility of the composites. Besides, due to the action of the hard intermetallic compound layer, with the increase in tensile deformation, a large number of GND are gradually accumulated in the Cu and Al layers near the interface, resulting in remote back stress, which makes the softer Cu and Al layers obtain higher strength. At the same time, the back stress caused by GND will induce strain hardening, which helps to maintain ductility, so that Cu/Al composites have higher plastic deformation ability while improving mechanical properties.

Preparation of laminated Cr3C2/Cu composites by direct ink writing and pressureless infiltration

Near-net shaping of laminated Al/Al2O3 composites by direct ink writing and pressure infiltration

Fabrication and Microstructure of C/Cu Composites

Enhanced Wetting and Properties of Carbon/carbon-Cu Composites with Cr 3 C 2 Coatings by Cr-solution Immersion Method

Beyond the Dimensional Limitation in Bio-Inspired Composite: Insertion of Carbon Nanotubes Induced Laminated Cu Composite and the Simultaneously Enhanced Strength and Toughness

Synthesis of damage-tolerant Cu-matrix composites with nacre-inspired laminate-reticular hierarchical architecture via tuning compositional wettability

Multilayered W-Cu composites with enhanced strength, electrical conductivity and wear resistance

Mechanical behavior and microstructure of 3D-printed carbon nanotubes-reinforced Cu composite

Synchronously improved mechanical strength and electrical conductivity of Carbon/Copper composites by forming Fe<sub>3</sub>C interlayer at C/Cu interface

A novel approach to fabricate layered RGO/Cu composites with excellent mechanical properties

Thin-Copper-Layer-Induced Early Fracture in Graphene-Nanosheets (Gnss)-Reinforced Copper-Matrix-Laminated Composites

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

High strength-tough and super-dispersed carbonized polymer dots reinforced copper composites fabricated by ultrasonic spray pyrolysis

Preparation and Interface Structure of CTCp/Cr26 Composites with the Pinning Effect

Understanding wetting mechanism of pure Cu on C/C composites modified by chromium carbide

Role of Structural Parameters on Strength-Ductility Combination of Laminated Carbon Nanotubes/copper Composites

Enhanced Mechanical Properties and High Electrical Conductivity in Multiwalled Carbon Nanotubes Reinforced Copper Matrix Nanolaminated Composites

Enhancing The Interlaminar Fracture Resistance Of Laminated Composites By Using Continuous Carbon Nanotube Films

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Preparation and fracture behavior of bionic layered SiCp/Al composites by tape casting and pressure infiltration

Fabrication and microstructure evolution of Csf/ZrB2-SiC composites via direct ink writing and reactive melt infiltration