Abstract:The use of carbon nanotubes (CNTs) as the reinforcing phase to prepare copper-based composite materials can improve the strength and high conductivity of copper-based conductors. In order to analyze the effect of surface oxidation modification on the structural properties of carbon nanotubes and its strengthening effect on composite materials, this article combines heterogeneous copolymerization liquid phase mixing method and spark plasma sintering molding method; prepares the carbon nanotubes/copper composite materials using carbon nanotubes under different oxidation treatment conditions as the reinforcing phase (the volume fraction of carbon nanotubes is 3%); and characterizes the microstructure, mechanical properties, and electrical and thermal conductivity of the composite material. Studies have shown that the tensile strength and hardness of composite materials first increase with the increase of CNT oxidation treatment time and then decrease with the increase of oxidation treatment time. When the oxidation treatment time is 4 h, CNTs are uniformly dispersed in the matrix while maintaining good structural integrity and load-bearing capacity, and the composite material has the highest mechanical properties. The tensile strength of the composite material made of 80‐ nm CNTs reaches 452.4 MPa, which is 1.6 times that of pure copper, and the hardness reaches 127.4HV, which is twice that of pure copper. The electrical conductivity and thermal conductivity of the composite material first increase with the increase of the oxidation treatment time of carbon nanotubes and then decrease with the increase of the oxidation treatment time. The 80 nm CNT reinforced composite material has better CNT dispersion performance and higher conductivity than that of 15 nm CNT preparation. The electrical conductivity of the composite material reaches the maximum value of 92% IACS when the CNT oxidation treatment time is 4 hours, which is 95% of the pure copper sample, and the electrical conductivity is significantly better than that of the CNT/Cu composite material and copper alloy prepared by other methods. The thermal conductivity of composite materials is lower than that of pure copper. The thermal conductivity of carbon nanotubes with an oxidation treatment time of 2 h decreases most obviously, indicating that the thermal resistance generated by the interface and agglomeration phases in the composite material affects its thermal conductivity.

Role of Structural Parameters on Strength-Ductility Combination of Laminated Carbon Nanotubes/copper Composites

MODELLING THE YIELD STRENGTH AND DUCTILITY IN COMPOSITE NANOTWINNED COPPER

Simulating Size and Volume Fraction-Dependent Strength and Ductility of Nanotwinned Composite Copper

Beyond the Dimensional Limitation in Bio-Inspired Composite: Insertion of Carbon Nanotubes Induced Laminated Cu Composite and the Simultaneously Enhanced Strength and Toughness

Achieving high ductility in layered carbon nanotube/copper composite prepared by composite electrodeposition

Enhanced Mechanical Properties and High Electrical Conductivity in Multiwalled Carbon Nanotubes Reinforced Copper Matrix Nanolaminated Composites

Overcoming Strength-Ductility Trade-off by Building a Micro-Nano Laminated Structure Based on an Ultralow Amount of Single-Dispersed Carbon Nanotubes

Thin-Copper-Layer-Induced Early Fracture in Graphene-Nanosheets (Gnss)-Reinforced Copper-Matrix-Laminated Composites

Effects of Ply-Orientation on Microstructure and Properties of Super-Aligned Carbon Nanotube Reinforced Copper Laminar Composites

Achieving good strength‐plasticity compatibility in Cu composites via carbon nanotube (CNT)‐induced heterogeneous bimodal structure

Enhancement mechanisms of mechanical, electrical and thermal properties of carbon nanotube-copper composites: A review

Improving the strength-ductility synergy of carbon nanotubes reinforced Cu matrix composites through interfacial regulation

Enhancement of mechanical properties and conductivity in carbon nanotubes (CNTs)/Cu matrix composite by surface and intratube decoration of CNTs

Investigation of the mechanical behavior of the carbon nanotubes coated copper composite materials

Interfacial Bonding Improvement through Nickel Decoration on Carbon Nanotubes in Carbon Nanotubes/Cu Composite Foams Reinforced Copper Matrix Composites

Attaining the strength-plasticity-electricity balance of carbon nanotube/Cu composites through combining the intragranular carbonized polymer dots distribution

Remarkable improvement of mechanical properties of layered CNTs/Al composites with Cu decorated on CNTs

Enhancing The Interlaminar Fracture Resistance Of Laminated Composites By Using Continuous Carbon Nanotube Films

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes

Effect of Surface Modification of Carbon Nanotubes on the Properties of High-Strength and High-Conductivity Copper Matrix Composites

Mechanical and Conductive Properties of Cu Matrix Composites Reinforced by Oriented Carbon Nanotubes with Different Coatings