Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Enhancement Mechanisms of the Power Conversion Efficiency for the P3HT:PCBM Bulk Heterojunction Solar Cells with a LiF Cathode Buffer Layer Due to Thermal Annealing

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

All-inorganic, Hole-Transporting-layer-free, Carbon-Based CsPbIBr2 Planar Perovskite Solar Cells by a Two-Step Temperature-Control Annealing Process

Study of the effect of annealing process on the performance of P3HT/PCBM photovoltaic devices using scanning-probe microscopy

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

Thermal Annealing Effect on Ultrafast Charge Transfer in All-Polymer Solar Cells with a Non-Fullerene Acceptor N2200

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Charge transport and extraction of PTB7:PC71BM organic solar cells: effect of film thickness and thermal-annealing

Performance improvement of annealing-free P3HT : PCBM-based polymer solar cells via 3-methylthiophene additive

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

Annealing Of P3ht:Pcbm Blend Film-The Effect On Its Optical Properties

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Enhancement of the Efficiency and Stability of Planar P-I-n Perovskite Solar Cells Via Incorporation of an Amine-Modified Fullerene Derivative As a Cathode Buffer Layer

Study on the Influence of Embedded Structure of Carbon Quantum Dots of the Organic Solar Cells with the Territory Active Layer Structure of P3HT: PC61BM: CQDs

Improving the Performance of Organic Light-Emitting Diodes Containing BCP/LiF/Al by Thermal Annealing

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Effect of Device Fabrication Conditions on Photovoltaic Performance of Polymer Solar Cells Based on Poly(3-Hexylthiophene) and Indene-C70 Bisadduct

Optimization of Bulk Heterojunction Organic Photovoltaics

Enhancement of the power conversion efficiency by expanding the absorption spectrum with fluorescence layers.

Improvement of Surface Morphology of Thin ?lms and Performance by "electrical Annealing" on Polymer Solar Cells