Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Effect of Device Fabrication Conditions on Photovoltaic Performance of Polymer Solar Cells Based on Poly(3-Hexylthiophene) and Indene-C70 Bisadduct

Analysis of the Effect of Active Layer Thickness on Polymer Solar Cell Performance Based on Optical and Opto-Electronic Model

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Study of the effect of annealing process on the performance of P3HT/PCBM photovoltaic devices using scanning-probe microscopy

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Comparison Of Small Amounts Of Polycrystalline Donor Materials In C-70-Based Bulk Heterojunction Photovoltaics And Optimization Of Dinaphthothienothiophene Based Photovoltaic

Optimization of Bulk Heterojunction Organic Photovoltaics

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

Performance improvement of annealing-free P3HT : PCBM-based polymer solar cells via 3-methylthiophene additive

Enhanced open-circuit voltage of two side chain conjugated polythiophene derivatives blended with indene-C60 bisadduct

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Charge transport and extraction of PTB7:PC71BM organic solar cells: effect of film thickness and thermal-annealing

Investigation of photovoltaic properties of poly(3-hexylthiophene): Polynaphthalene-bithiophene heterostructure devices

P3ht: Pcbm Solar Cells-The Choice Of Source Material

The Effect of Atmosphere and ZnO Morphology on the Performance of Hybrid Poly(3-hexylthiophene)/ZnO Nanofiber Photovoltaic Devices

Effect of linear side-chain length on the photovoltaic performance of benzodithiophene-alt-dicarboxylic ester terthiophene polymers

Thermal Annealing Effect on Ultrafast Charge Transfer in All-Polymer Solar Cells with a Non-Fullerene Acceptor N2200

High-Yield Synthesis And Electrochemical And Photovoltaic Properties Of Indene-C-70 Bisadduct

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-20D:PC71 BM Polymer Solar Cells