Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Hybrid Nonfused Electron Acceptors with Perylene Diimide Pendants for Organic Solar Cells

[6,6]-Phenyl-c61-butyric Acid 2-((2-(dimethylamino)ethyl)(methyl)amino)-ethyl Ester As an Acceptor and Cathode Interfacial Material in Polymer Solar Cells

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Non-halogenated solvent processable wide bandgap polymer based on carboxylate-substituted benzodithiophene for high-efficiency polymer solar cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Design, Application, and Morphology Study of a New Photovoltaic Polymer with Strong Aggregation in Solution State

High-performance polymer solar cells based on terpolymer composed of one donor and two acceptors processed with non-halogenated solvent

A Copolymer of Benzodithiophene with TIPS Side Chains for Enhanced Photovoltaic Performance

Suppressed Charge Recombination in Polymer Solar Cells Based on Perylene Diimide Derivative Acceptors Via Solvent Vapor Annealing

Solid Additive Tuning Polymer Blend Morphology Enables Non-halogenated-solvent All-polymer Solar Cells with Efficiency over 17%

Layer‐by‐Layer Solution‐Processed Low‐Bandgap Polymer‐PC61BM Solar Cells with High Efficiency

A Copolymer Based on Benzo[1,2-B:4,5-B′]dithiophene and Quinoxaline Derivative for Photovoltaic Application

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Benzobisthiazole-Substituted Terpolymers for Non-Halogenated Solvent-Processed Polymer Solar Cells with Enhanced Efficiency, Thermal Stability and Mechanical Robustness

Polythiophenes with carboxylate side chains and vinylene linkers in main chain for polymer solar cells

All-Polymer Solar Cells Based on A Blend of Poly[3-(10-N-Octyl-3-Phenothiazine-Vinylene)Thiophene-Co-2,5-Thiophene] and Poly[1,4-Dioctyloxyl-P-2,5-Dicyanophenylenevinylene]

A High‐Mobility Low‐Bandgap Copolymer for Efficient Solar Cells

Synergetic Solvent Engineering of Film Nanomorphology to Enhance Planar Perylene Diimide-Based Organic Photovoltaics.

Design of a thiophene-fused benzotriazole unit as an electron acceptor to build D–A copolymers for polymer solar cells