Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

All-Polymer Solar Cells Based on A Blend of Poly[3-(10-N-Octyl-3-Phenothiazine-Vinylene)Thiophene-Co-2,5-Thiophene] and Poly[1,4-Dioctyloxyl-P-2,5-Dicyanophenylenevinylene]

Efficient All-Polymer Solar Cells Based on Blend of Tris(thienylenevinylene)-Substituted Polythiophene and Poly[perylene Diimide-Alt-bis(dithienothiophene)]

All-Polymer Solar Cells with Perylenediimide Polymer Acceptors

High‐Efficiency P3HT‐Based All‐Polymer Solar Cells with a Thermodynamically Miscible Polymer Acceptor

Achieving over 17% efficiency of ternary all-polymer solar cells with two well-compatible polymer acceptors

Enhanced open-circuit voltage of two side chain conjugated polythiophene derivatives blended with indene-C60 bisadduct

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Rationally pairing photoactive materials for high-performance polymer solar cells with efficiency of 16.53%

All-polymer solar cells based on PTACs/P3HT blends with large open-circuit voltage

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

n-Octyl substituted quinoxaline-based polymer donor enabling all-polymer solar cell with efficiency over 17%

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Improvement in Power Conversion Efficiency of All-Polymer Solar Cells Enabled by Ultrafast Channels for Charge Dynamics

An Improved Performance of All Polymer Solar Cells enabled by Sequential Processing via Non-halogenated Solvents

Over 18% efficiency ternary all-polymer solar cells with high photocurrent and fill factor

A chlorinated polymer promoted analogue co-donors for efficient ternary all-polymer solar cells

All-polymer Solar Cells Based on Side-Chain-isolated Polythiophenes and Poly(perylene Diimide-Alt-dithienothiophene)

Improved Charge Generation via Ultrafast Effective Hole‐Transfer in All‐Polymer Photovoltaic Blends with Large Highest Occupied Molecular Orbital (HOMO) Energy Offset and Proper Crystal Orientation

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

Binary All‐polymer Solar Cells with a Perhalogenated‐Thiophene‐Based Solid Additive Surpass 18% Efficiency