Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

All-polymer solar cells based on PTACs/P3HT blends with large open-circuit voltage

Donor-Acceptor Photovoltaic Polymers Based On 1,4-Dithienyl-2,5-Dialkoxybenzene With Intramolecular Noncovalent Interactions

High‐Efficiency P3HT‐Based All‐Polymer Solar Cells with a Thermodynamically Miscible Polymer Acceptor

All-polymer Solar Cells Based on Side-Chain-isolated Polythiophenes and Poly(perylene Diimide-Alt-dithienothiophene)

All-Polymer Solar Cells with Perylenediimide Polymer Acceptors

All-Polymer Solar Cells Based on A Blend of Poly[3-(10-N-Octyl-3-Phenothiazine-Vinylene)Thiophene-Co-2,5-Thiophene] and Poly[1,4-Dioctyloxyl-P-2,5-Dicyanophenylenevinylene]

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

8.30% Efficiency P3HT-based All-Polymer Solar Cells Enabled by a Miscible Polymer Acceptor with High Energy Levels and Efficient Electron Transport

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Dithiazolyl-benzothiadiazole-containing polymer acceptors: Synthesis, characterization, and all-polymer solar cells

Efficient All-Polymer Solar Cells Based on Blend of Tris(thienylenevinylene)-Substituted Polythiophene and Poly[perylene Diimide-Alt-bis(dithienothiophene)]

Polythiophenes with carboxylate side chains and vinylene linkers in main chain for polymer solar cells

Molecular Optimization on Polymer Acceptor Enables Efficient All‐Polymer Solar Cell with High Open‐Circuit Voltage of 1.10 V

Benzotriazole‐Based Polymer Acceptor for High‐Efficiency All‐Polymer Solar Cells with High Photocurrent and Low Voltage Loss

Polymerized small-molecule acceptors based on vinylene as π-bridge for efficient all-polymer solar cells

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

Polythiophene and its derivatives for all-polymer solar cells

Synthesis And Photovoltaic Properties From Inverted Geometry Cells And Roll-To-Roll Coated Large Area Cells From Dithienopyrrole-Based Donor-Acceptor Polymers

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Highly Efficient and Stable All-Polymer Solar Cells Enabled by Near-Infrared Isomerized Polymer Acceptors

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent