Abstract:This work presents research results concerning to the fabrication of hybrid solar cells in a superstrate configuration with the following structure: glass/SnO 2 :F/ZnO + CdS/CdTe + CdCl 2 -TT/PEDOT:PSS-TT/Cu-Mo. After Cadmium Telluride (CdTe) absorber layer processing, the organic conjugated polymer Poly(3,4-ethylenedioxythiophene): poly(styrene sulphonate) (PEDOT:PSS) was deposited with a thickness around 50 nm, then a thermal annealing (TA) was carried out varying annealing time (20-40 min) and temperature (80-120 °C). The physical properties and output electrical parameters of the devices were measured and compared with a reference solar cells without TA. A decrease of the resistivity values was reached as a result of the incorporation of PEDOT:PSS on CdTe as a hole transport layer. CdTe/PEDOT:PSS structure was characterized by profilometry, four-probe method, UV–Vis spectroscopy, Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and Raman spectroscopy. The electrical performance of the fabricated hybrid solar cells was analysed through the current density vs. voltage (J vs. V) characteristic, External Quantum Efficiency (EQE) measurements and the values spread distribution for each electrical parameter was also discussed. A highest conversion efficiency around 15.2% was obtained for a device in which the TA was performed at 100 °C during 30 min with output electrical parameters values of V oc ~ 0.778 V, J sc ~ 34.0 mA/cm 2 , FF ~ 0.55 and EQE values above 55%, resulting this in an improvement of the use of PEDOT:PSS in hybrid solar cells. A monitoring of the degradation effect of the output electrical values was carried out after a period of 24 months and an average degradation rate around 20% was found, however for devices processed at higher temperatures of TA, degradation rate of the conversion efficiency was at least 3%.

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network Morphology

Photovoltaic cells based on dye-sensitisation of single-wall carbon nanotubes in a polymer matrix

Thermal Annealing Effect on Ultrafast Charge Transfer in All-Polymer Solar Cells with a Non-Fullerene Acceptor N2200

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

Investigation of the effects of thermal annealing to PEDOT:PSS on the photovoltaic response of hybrid solar cells

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-20D:PC71 BM Polymer Solar Cells

Enhancement of inverted organic solar cell parameters by post-production annealing process

Carbon nanotubes as electron acceptors in polymeric photovoltaics

Effect of Device Fabrication Conditions on Photovoltaic Performance of Polymer Solar Cells Based on Poly(3-Hexylthiophene) and Indene-C70 Bisadduct

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-2OD:PC<sub>71</sub>BM Polymer Solar Cells

Single-wall Carbon Nanotube/conjugated Polymer Photovoltaic Devices

Study of the effect of annealing process on the performance of P3HT/PCBM photovoltaic devices using scanning-probe microscopy

High-Temperature Annealing of TiO2 Nanotube Membranes for Efficient Dye-Sensitized Solar Cells

Photovoltaic Properties of Dye Functionalized Single-Wall Carbon Nanotube/Conjugated Polymer Devices

Thermal Radiation Annealing for Overcoming Processing Temperature Limitation of Flexible Perovskite Solar Cells

Effective Mobility and Photocurrent in Carbon Nanotube–polymer Composite Photovoltaic Cells

Thermal-Induced Performance Decay of the State-of-the-Art Polymer: Non-Fullerene Solar Cells and the Method of Suppression

Improvement of Photovoltaic Performance of Dye-Sensitized Solar Cell by Post Heat Treatment of Polymer-Capped Nano-Platinum Counterelectrode