Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network Morphology

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-20D:PC71 BM Polymer Solar Cells

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Silicon Nanocrystal Conjugated Polymer Hybrid Solar Cells with Improved Performance

Simultaneous enhanced efficiency and thermal stability in organic solar cells from a polymer acceptor additive

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-2OD:PC<sub>71</sub>BM Polymer Solar Cells

Optimizing the Morphology of All-Polymer Solar Cells for Enhanced Photovoltaic Performance and Thermal Stability

Thermal-Induced Performance Decay of the State-of-the-Art Polymer: Non-Fullerene Solar Cells and the Method of Suppression

End‐extended Conjugation Strategy to Reduce the Efficiency‐Stability‐Mechanical Robustness Gap in Binary All‐Polymer Solar Cells

Nanoscale control of the network morphology of high efficiency polymer fullerene solar cells by the use of high material concentration in the liquid phase

An Optimized Fibril Network Morphology Enables High‐Efficiency and Ambient‐Stable Polymer Solar Cells

High-efficiency all-polymer solar cells based on a pair of crystalline low-bandgap polymers.

Reduction in the Temperature Coefficient of Photovoltaic Efficiency in All-Polymer Solar Cells Using Molecular Order

Stepwise heating in Stille polycondensation toward no batch-to-batch variations in polymer solar cell performance

Tailoring polymer acceptors by electron linkers for achieving efficient and stable all-polymer solar cells

Geometry design of tethered small-molecule acceptor enables highly stable and efficient polymer solar cells

Enabling Highly Efficient and Thermal‐stable Polymer Solar Cells through Semi‐alloy Acceptors Composed of A Hinge‐like Dimer: A Versatile Doping Protocol

Improving Polymer Solar Cell Performances By Manipulating The Self-Organization Of Polymer

Characterizing the Morphology and Efficiency of Organic Solar Cells by Multiscale Simulations