Abstract:In this paper, we use the nonlinear hardening stiffness of drive mode deal with the contradiction between gain and bandwidth of the linear micro-gyroscope, to improve the bandwidth and gain in sense direction. Firstly, in order to adjust the distance between two resonant peaks, we changed an incomplete two-degree-of-freedom(2-DoF) sense mode system of the micro-gyroscope into a complete 2-DoF system. Afterward, according to the given nonlinear coefficient of stiffness of drive mode, the structure size of driving micro-beams was designed to obtain a nonlinear micro-gyroscope with controllable stiffness. Finally, we investigated the effects of peaks spacing, damping, and driving nonlinearity on gain and bandwidth, and the nonlinear micro-gyroscope was optimized by orthogonal experiment method and response surface method. The results reveal that the peaks spacing has a great influence on the gain and bandwidth of both linear and nonlinear micro-gyroscopes. The larger the peaks spacing, the lower the gain, but higher gain can be achieved when the resonant frequency of the drive mode is close to the lower-order resonant frequency of the sense mode. Driving nonlinearity leads to the response peak of the Coriolis force to have a hardening characteristic, thus forming a wide platform in the sense direction. Hardening of the response peak of the Coriolis force allows the micro-gyroscope to obtain a higher gain while the bandwidth of the sense mode is also greatly improved. In addition, parameter optimization can make the gain and bandwidth of the micro-gyroscope optimal. When the peaks spacing is small and the nonlinear stiffness coefficient is about 1012.2, under the premise that the gain is basically constant, the bandwidth of the sense mode increases about 1.76 times compared with the linear gyroscope. Damping can suppress the influence of nonlinearity in a micro-gyroscope system. Within a certain range, the frequency response of the nonlinear micro-gyroscope tends to be a linear system with the increase in damping, resulting in narrower bandwidth and lower gain.

A New Robust Four Degree-of-Freedom Gyroscope Design

A Bulk Micromachined Gyroscope With Improved Quality-Factors At Atmospheric Pressure

Constant-frequency Oscillation Control for Vibratory Micro-Machined Gyroscopes

A MICROMECHANICAL MODE-MATCHED GYROSCOPE USING STIFFNESS NONLINEARITY AND ELECTROSTATIC TUNING

A 0.09°/h Bias-Instability MEMS Gyroscope Working with a Fixed Resonance Frequency

Design and optimization of a resonant output frequency gyroscope for robust sensitivity and bandwidth performance

Bandwidth optimization design of a multi degree of freedom MEMS gyroscope

Design and implementation of a fully-decoupled tuning fork (FDTF) MEMS vibratory gyroscope for robustness improvement

Design and Simulation of a Dual-Axis Sensing Decoupled Vibratory Wheel Gyroscope

Optimization of Sensitivity for a Novelly-Designed MEMS Resonant Gyroscope

Acceleration-insensitive fully-decoupled tuning fork (FDTF) MEMS vibratory gyroscope with 1°/HR BIAS instability

Force Rebalance Controller Synthesis for A Micromachined Vibratory Gyroscope Based on Sensitivity Margin Specifications

Innovation of Flat Gyro: Center Support Quadruple Mass Gyroscope

Optimal Design Of A Center Support Quadruple Mass Gyroscope (Csqmg)

Design and Simulation of Novel MEMS Resonant Gyroscope

Design and Analysis of Optomechanical Micro-Gyroscope for Angular-Vibration Detection

High-performance Silicon Micromachined Resonant Gyroscope

Design of a Micro-Electro Mechanical System Quad Mass Gyroscope with Compliant Mechanical Amplification

A novel robust design method for the sense mode of a MEMS vibratory gyroscope based on fuzzy reliability and Taguchi design

Design of rebalance loop for an electrostatically suspended micromachined gyroscope

Design, Dynamics, and Optimization of a 3-DoF Nonlinear Micro-Gyroscope by Considering the Influence of the Coriolis Force