Abstract:Titanate nanotubes were synthesized hydrothermally from commercial TiO2 nanoparticles in the presence of NaOH; after calcination at 400°C, TiO2 nanotubes were obtained, which were used as the support to prepare manganese catalyst (MnOx/TiNT) by wet impregnation for the low-temperature selective catalytic reduction (SCR) of NO. The results of Brunauer, Emmett and Teller study, transmission electron microscopy, X-ray diffraction, and thermogravimetric measurements showed that TiO2 nanotubes exist in a well-defined TiO2 anatase phase after calcination at 400°C and that manganese particles are highly dispersed on the wall of TiO2 nanotubes. The effects of active-component loading, space velocity, oxygen content, [NH3]/[NO] ratio, and NO concentration on the SCR performance of MnOx/TiNT were investigated in a simulated flue gas. Under the reaction conditions of 150°C, [NH3]/[NO] of 1.2, [O2] of 3%, [NO] of 0.06%, gas hour space velocity of 23613.8 h−1, and Mn loading of 5–15%, NO conversion exceeds 95%. The catalyst is deactivated in the presence of H2O at 180°C, but its activity can be recovered almost completely by cutting off H2O. Moreover, higher resistance to H2O is observed at higher temperatures. The presence of SO2 can also deactivate the catalyst gradually; however, the catalyst shows better resistance to SO2 in the presence of H2O than in its absence. The SCR activity of the MnOx/TiNT catalyst that is deactivated by SO2 increases gradually after cutting off H2O and SO2 but cannot be restored to its initial level.

Catalytic Reduction of NO by NH3 over Fe–Cu–OX/CNTs-TiO2 Composites at Low Temperature

Activation of Fast Selective Catalytic Reduction of NO by NH3 at Low Temperature over TiO2 Modified CuOX-CeOX Composites

Synergy Between FeOX and CuOX in FeCuOX/TiO2-hBN Composites for NO Reduction with NH3

Low-Temperature Catalytic Reduction of Nitrogen Monoxide with Carbon Monoxide on Copper Iron and Copper Cobalt Composite Oxides

Low temperature selective catalytic reduction of NOx by NH3 over Cu modified V2O5/TiO2–carbon nanotube catalyst

Selective catalytic reduction of NO with NH3 over CuOX-carbonaceous materials

Catalytic Reduction of NO_x over MnO_x Coated TiO_2 Nanotube Arrays

Low-temperature Fe–MnO 2 nanotube catalysts for the selective catalytic reduction of NO x with NH 3

Selective catalytic reduction of NOX with ammonia over Mn–Ce–OX/TiO2-carbon nanotube composites

Temperature-Dependent Effects of SO2 on Selective Catalytic Reduction of NO over Fe–Cu–OX/CNTs–TiO2 Catalysts

Interaction between SO2 and Fe–Cu–Ox/CNTs–TiO2 catalyst and its influence on NO reduction with NH3

Low-Temperature Selective Catalytic Reduction of NO by CO in the Presence of O-2 over Cu:Ce Catalysts Supported by Multiwalled Carbon Nanotubes

A Ce–Cu–Ti oxide catalyst for the selective catalytic reduction of NO with NH3

Study on Catalytic Reduction of NO on CuO/TiZrO4 in the Presence of Excess Oxygen

Catalytic Reduction of NO with NH 3 over V 2 O 5 -MnO X /TiO 2 -Carbon Nanotube Composites

Performance of a Novel CuSO4-CeO2/TiO2-SiO2 Catalyst for NO Reduction with NH3 at Low Temperature

MnOx-SnO2 Catalysts Synthesized by a Redox Coprecipitation Method for Selective Catalytic Reduction of NO by NH3

Low Temperature Selective Catalytic Reduction of NO over Manganese Supported on TiO2 Nanotubes

Fe and Mn mixed oxide catalysts supported on Sn-modified TiO 2 for the selective catalytic reduction of NO with NH 3 at low temperature

Enhanced Catalytic Performance of V2O5–WO3/Fe2O3/TiO2microspheres for Selective Catalytic Reduction of NO by NH3

Highly dispersed V2O5/TiO2 modified with transition metals (Cu, Fe, Mn, Co) as efficient catalysts for the selective reduction of NO with NH3