Abstract:The unsatisfactory high-temperature performance of commonly used silicon carbide (SiC)-based ceramics calls for a novel approach for their reinforcement. We present the in situ preparation of a SiC-based composite with uniformly dispersed titanium boride (TiB2) particles using titanium carbide and boron carbide as raw materials. Notably, the uniform incorporation of 25 wt%TiB2 results in the SiC–TiB2 composite with excellent tribological and self-lubricating properties at high temperatures. The SiC–TiB2 composite shows a friction coefficient of 0.20 and a specific wear rate of 5.77 × 108 mm3/(N mm), which are 4.75 times and ~ 5.2 times lower than that of the bare SiC ceramic at 1000 °C, respectively. The wear mechanism of a self-mated couple of the SiC–TiB2 composite is unraveled to be the tribo-oxidization. Since intimate contact exists between the oxidizing layer and the transitional layer of the fractured surface, the friction surface possessing plastic deformation properties may transit from brittle to plastic or elastic. The "Pin Effect" exhibited by TiB2 particles in the SiC–TiB2 composite deflects the crack propagation route. Meanwhile, a change in stress distribution, a decrease in the stress intensity of slight crack frontier, and an increase in "the threshold value" of crack propagation occur. The type (I + II) and type (I + III) complex cracks in fracture mechanics propagate non-flatly in the wearing process of the self-mated couple of the SiC–TiB2 composite. Besides, a fine yield deformation zone exists on the crack tip. Consequently, the "threshold value" of crack propagation fluctuates dynamically between "upper bound value" and "lower bound value" following the change in the valid length of actual crack propagation, thus delaying the fracture of the SiC–TiB2 composite.

High-Temperature Tribological Performance of Ti 3 SiC 2 /tial Self-Lubricating Composite Against Si 3 N 4 in Air

Self-lubricating behavior caused by tribo-oxidation of Ti3SiC2/Cu composites in a wide temperature range

Effect of Temperature on Tribological Properties of Tial Based Self-Lubricating Composites

Friction and wear performance of a NiAl-8 wt% serpentine-2 wt%TiC composite at high temperatures

High-temperature tribological properties of Si 3 N 4 /TiC ceramic with bionic surface textures and DLC coatings

Investigation on Microstructure and Wear Behavior of the NiAl–TiC–Al2O3 Composite Fabricated by Self-Propagation High-Temperature Synthesis with Extrusion

Tribological Properties of Ti3SiC2 Coupled with Different Counterfaces

Tribological properties of self-healing NiCrAlY/Cr3C2-Ti3AlC2 coating at high temperatures

Synthesis and Tribological Characterization of Ti3SiC2/ZnO Composites

High-performance TiN Reinforced Sialon Matrix Composites: A Good Combination of Excellent Toughness and Tribological Properties at a Wide Temperature Range

High-temperature Tribological Properties of Si3N4/TiC Ceramic with Bionic Surface Textures and DLC Coatings

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

Sn-containing Si3N4-based composites for adaptive excellent friction and wear in a wide temperature range

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

High-Temperature Tribological Behavior of Fast-Hot-Pressed NiCr/Cr3C2-LaF3 Self-Lubrication Composite

Analysis of oxidation behavior of laser cladding SiC-Ti based composite strengthening coating

Tribological properties of NbTiTa self-lubricating medium-entropy composites over a wide temperature range

Wear Behavior of TiN/TiAlSiN Nanocomposite Multilayer Coatings from Ambient Temperature to Medium Temperature

Tribo-oxide Competition and Oxide Layer Formation of Ti3SiC2/CaF2 Self-Lubricating Composites during the Friction Process in a Wide Temperature Range

Tribological Behavior of Ti3SiC2 and Ti3SiC2/Pb Composites Sliding Against Ni-based Alloys at Elevated Temperatures

High-Temperature Wear Behavior and Mechanisms of Self-Healing NiCrAlY-Cr3C2-Ti2SnC Coating Prepared by Atmospheric Plasma Spraying