Abstract:Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Ahead of Print. In this work, Fe-2Cu-0.8C-CaF2 self-lubricating composites with calcium fluoride solid lubricant (3 □ 12 wt.%) were examined for their friction and wear at 5 and 10 m/s, at 500 °C. Addition of CaF2 decreased density and hardness of composites. During sliding, materials gained weight due to oxidation. Compared to the base matrix (Fe-2Cu-0.8C), composites showed lower weight gain and lower coefficient of friction. Increase in porosity with CaF2 content increased oxidation resulting in higher weight gain and increased friction due to wear debris abrasion. Increase in speed reduced weight gain due to higher material loss. Adhesion was the dominant wear mechanism in base matrix; delamination and wear debris abrasion in composites. Temperature rise at sliding surfaces was theoretically estimated. Increase in speed increased temperature, which reduced friction due to softening and shearing of solid lubricant. Composite with 3 wt.% CaF2 showed least surface damage and 6 wt.% showed lowest coefficient of friction, i.e., lower by 16% and 10% at 5, 10 m/s than base matrix. Tribological response of the composites to a broad range of applied parameters, viz. speed, load and temperature taken from earlier works and present work is briefly summarized. The study suggests the dominant role of CaF2 content and the wear debris in altering the tribological response. Further, the stability of the developed composites at high temperature and high load conditions was also established. The study suggests that the developed composites could serve high-load and high-temperature applications for heavy machinery such as bearings, shafts and gears.

Tribological properties of NbTiTa self-lubricating medium-entropy composites over a wide temperature range

Enhancing High-Temperature Wear Resistance by Constructing the Amorphous-Crystal Heterointerface Structure in WO3/TiO2 Composite Coatings

Tribological performance of a cost-effective CrFeNiAl0.3Ti0.3 high entropy alloy based self-lubricating composite in a wide temperature range

Effect of Temperature on Tribological Properties of Tial Based Self-Lubricating Composites

Microstructures and Tribological Properties of TiC Reinforced FeCoNiCuAl High-Entropy Alloy at Normal and Elevated Temperature

Tribological behavior of NiCrW-based self-lubricating composites against IC10 alloy under high temperature and extremely slow sliding speed

High-temperature Tribological Properties of the Novel NiCr(MoNb)x-Ag Self-Lubricating Composite Films

High temperature tribological response of Fe-2Cu-0.8C-CaF2 self-lubricating composites at high speeds

High-Temperature Tribological Behavior of Al0.3Cr0.5Fe1.5Mn0.5Ni High-Entropy Alloys With Addition of Titanium and Carbon

High-Temperature Tribological Behavior of Fast-Hot-Pressed NiCr/Cr3C2-LaF3 Self-Lubrication Composite

Microstructure and tribological properties of TiZrV0.5Nb0.5Al refractory high entropy alloys at elevated temperature

Mechanical and tribological performance of (TiNbTaWMo)C high-entropy ceramics in a wide temperature range

High temperature tribology of CuMoTaWV high entropy alloy

A promising high temperature self-lubricating Cu-based superalloy with coherent cuboidal L12-γʹ phases

Wear Properties of NiAl Based Materials

Effects of the Environment and Temperature on the Tribological Behavior of TiZrHfNbTa Refractory High-Entropy Alloy

Tribological behavior of h -BN/Al 2 O 3 self-lubricating composites in extreme environments–Part I: Lubricating behavior and ultra-low friction coefficient mechanism in air environments from room temperature to 1200 °C

The study of mechanical and tribology properties at room- and high-temperature in a (NiCoFe)86.5(AlTi)12(WMoV)1.5 high-entropy alloy

High-Temperature Friction and Wear Behavior of Nickel-Alloy Matrix Composites with the Addition of Molybdate

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

Effects of Temperature and Normal Load on Tribological Behavior of Nickel-Based High Temperature Self-Lubricating Wear-Resistant Composite Coating