Abstract:In this paper, we present the design, fabrication and measurement results of a 2D scanning mirror actuated by 1 × 10 piezoelectric Pb(Zr,Ti)O3 (PZT) cantilever actuators integrated on a thin silicon beam. A combination of bulk silicon micromachining based on a silicon-on-insulator (SOI) substrate and thin-film surface micromachining on a 5 µm thick Si device layer is used to fabricate the device. Multi-layers of Pt/Ti/PZT/Pt/Ti are deposited as electrode materials. A large silicon mirror plate (5 mm × 5 mm) and a 1 × 10 PZT cantilever array arranged in parallel are formed after the backside release process. The ten PZT cantilever actuators are electrically isolated from one another. The device can operate in three modes: bending, torsional and mixed (or combinational) modes. In bending mode, the first resonant frequency was measured to be 30 Hz and an optical deflection angle of ±8° was obtained when all ten cantilevers were actuated at 9 Vpp. In torsional mode, the resonant frequency was measured to be 89 Hz and an optical deflection angle of ±4.6° was obtained by applying a gradually declining ac voltage started at 8 Vpp to two sets of actuators, where each set comprises five cantilever actuators of the said 1 × 10 array, i.e. 1–5 and 6–10. A 2D raster scanning pattern was achieved in the mixed mode when the bending mode was carried out by cantilever actuators of 4–7 and the torsional modes were exercised by two different sets of cantilever actuators, i.e. 1–3 and 8–10, under opposite biasing direction. This mixed mode operation mechanism demonstrates the first 2D raster scanning mirror-driven beam actuators.

Process Platform For High Aspect-Ratio Self-Aligned Vertical Comb Actuators

An Electrostatic Vertical Comb-Drive Micromirror with Self-Aligned Assembly

The BELST II Process for a Silicon High-Aspect-ratio Micromaching Vertical Comb Actuator and Its Applications

Realization of Three-Dimensionally MEMS Stacked Comb Structures for Microactuators Using Low-Temperature Multi-Wafer Bonding with Self-Alignment Techniques in CMOS-Compatible Processes

A Poly-Si-Based Vertical Comb-Drive Two-Axis Gimbaled Scanner for Optical Applications

MEMS Scanning Mirror with Vertical Comb Actuator Based on Latching Technique

Driving Principle and Stability Analysis of Vertical Comb-Drive Actuator for Scanning Micromirrors

Surface Micromachined Mirror Based on Pre-Stress Comb-Drive Actuator

Design of Novel Sequential Engagement Vertical Comb Electrodes for Analog Micromirror

A Large Out-of-plane Motion Mechanism for Optical Applications

Hybrid Electrostatic Actuator for Micromirror Tilting

Large Stroke Staggered Vertical Comb-Drive Actuator for the Application of a Millimeter-Wave Tunable Phase Shifter

Design, modeling, analysis and testing of a novel piezo-actuated XY compliant mechanism for large workspace nano-positioning

Modeling and Optimization of a Novel ScAlN-Based MEMS Scanning Mirror with Large Static and Dynamic Two-Axis Tilting Angles

Torsion-mirror Actuators with Compound Electrostatic Driving Structures

Development of an Electrostatic Comb-Driven MEMS Scanning Mirror for Two-Dimensional Raster Scanning

Design of Butterfly Plate Piezoelectric Actuator with Dual Driving Electrodes for MEMS Micro-Mirror

Design and investigation of dual-axis electrostatic driving MEMS scanning micromirror

A Novel Piezoelectrically Actuated 2-Dof Compliant Micro/Nano-Positioning Stage with Multi-Level Amplification

A Novel Electrostatically Driven Micromirror with Lateral Comb Actuators and T-Shaped Torsion Bars

Novel Piezoelectric Actuation Mechanism for a Gimbal-Less Mirror in 2D Raster Scanning Applications