Abstract:The Peierls–Nabarro dislocation model is applied in this paper to investigate the [110] full dislocations on the (001), (111), and (1 ̄10) planes in pure Al, as well as the (110) small-angle tilting grain boundary (SATGB) composed of them. The findings demonstrate that the stress–strain fields of both dislocations and grain boundaries can be accurately described by a five-term single dislocation strain field. The Peierls stresses for the [110] edge-type dislocations on the (001), (111), and (1 ̄10) planes are 67.15 MPa, 114.93 MPa, and 847.56 MPa, respectively, exhibiting an increasing trend in magnitude. As the inter-dislocation distance decreases in the (110) SATGB of Al, the stress field, half-width, decomposition trend, and line energy of individual dislocations gradually decrease. The change in the line energy can be divided into three parts: Initially, there is a slow decrease when the distance is greater than ~200 Å. This is followed by a sharp drop in the line energy as the distance further decreases, with a slowing down of this trend at ~70 Å, where strain energy becomes dominant. In the final stage, the changes in the strained energy and core energy synergistically contribute. The (110) SATGB energy exhibits an increasing trend with the increment of the angle. The Peierls energy and force of the (110) SATGB composed of [110] full dislocations on the Al (001) and (111) surfaces exhibit minimal variation as the distance between dislocations changes, whereas a slight decrease is observed on the (110) surface. The present study provides valuable insights into the investigation of mechanical properties in Al alloys with nanometer-sized grains.

Study of Dislocation Boundary Structure in Al–Li Alloy During Bending

Inclination-governed Deformation of Dislocation-Type Grain Boundaries

DIC/EBSD Coupling Analysis of Microstructure Evolution and Strain Localization During Bending of Al-Li Alloy

Strain Localization and Damage Development in 2060 Alloy During Bending

Evolutions of Grain Orientation and Dislocation Boundary in Aa1050 Aluminum Alloy During Cold Rolling from Low to Medium Strains

Dislocation Boundary Structure from Low to Medium Strain of Cold Rolling AA3104 Aluminum Alloy

B12-P-08In Situ Observation of Dislocation Accumulation and Small Angle Grain Boundary Formation

Grain boundary decohesion in body-centered cubic Mg-Li-Al alloys

Grain Orientation Dependence of Extended Planar Dislocation Boundaries in Cold-Rolled Polycrystalline Aluminium

First-Principles Study of Physical Properties of (110) Symmetric Small-Angle Tilting Grain Boundary with Full Dislocation in Aluminum

Grain Orientation Dependence of Extended Planar Dislocation Boundaries in Rolled Aluminium

Dissociation of Dislocations in Al[sub 67]mn[sub 8]ti[sub 26] Deformed at Ambient and High Temperatures

Substructure and Boundary Structure of Deformed 18R Martensite in a Cu–Zn–Al Alloy

Faceting and Migration of Low Angle <100> Tilt Grain Boundaries in Pure Aluminum

Characterization Of Precipitates In Bend-Age-Formed 2124 Aluminum Alloy

Deformation Behavior and Mechanism of P-Type (bi,sb)2te3 Alloy During Three-Point Bending Test at Room Temperature

Orientation dependence of dislocation structure in surface grain of pure aluminium deformed in tension

A transmission electron microscopy study of dislocation structures in a directionally solidified Ni3Al-based alloy deformed at 850°C

Grain Structure and Microtexture Evolution During Superplastic Deformation of 5A90 Al-Li Alloy

The structure and mobility of the intervariant boundaries in 18R martensite in a Cu–Zn–Al alloy

Faceting and Migration of Low Angle Tilt Grain Boundaries in Pure Aluminum