Abstract:The Peierls–Nabarro dislocation model is applied in this paper to investigate the [110] full dislocations on the (001), (111), and (1 ̄10) planes in pure Al, as well as the (110) small-angle tilting grain boundary (SATGB) composed of them. The findings demonstrate that the stress–strain fields of both dislocations and grain boundaries can be accurately described by a five-term single dislocation strain field. The Peierls stresses for the [110] edge-type dislocations on the (001), (111), and (1 ̄10) planes are 67.15 MPa, 114.93 MPa, and 847.56 MPa, respectively, exhibiting an increasing trend in magnitude. As the inter-dislocation distance decreases in the (110) SATGB of Al, the stress field, half-width, decomposition trend, and line energy of individual dislocations gradually decrease. The change in the line energy can be divided into three parts: Initially, there is a slow decrease when the distance is greater than ~200 Å. This is followed by a sharp drop in the line energy as the distance further decreases, with a slowing down of this trend at ~70 Å, where strain energy becomes dominant. In the final stage, the changes in the strained energy and core energy synergistically contribute. The (110) SATGB energy exhibits an increasing trend with the increment of the angle. The Peierls energy and force of the (110) SATGB composed of [110] full dislocations on the Al (001) and (111) surfaces exhibit minimal variation as the distance between dislocations changes, whereas a slight decrease is observed on the (110) surface. The present study provides valuable insights into the investigation of mechanical properties in Al alloys with nanometer-sized grains.

Grain Orientation Dependence of Extended Planar Dislocation Boundaries in Rolled Aluminium

Grain Orientation Dependence of Extended Planar Dislocation Boundaries in Cold-Rolled Polycrystalline Aluminium

Evolutions of Grain Orientation and Dislocation Boundary in Aa1050 Aluminum Alloy During Cold Rolling from Low to Medium Strains

Dislocation Boundary Structure from Low to Medium Strain of Cold Rolling AA3104 Aluminum Alloy

Inclination-governed Deformation of Dislocation-Type Grain Boundaries

Orientation dependence of dislocation structure in surface grain of pure aluminium deformed in tension

The Grain Size and Orientation Dependence of Geometrically Necessary Dislocations in Polycrystalline Aluminum During Monotonic Deformation: Relationship to Mechanical Behavior

Critical Comparison of Dislocation Boundary Alignment Studied by TEM and EBSD: Technical Issues and Theoretical Consequences

Dislocations, Boundaries and Slip Systems in Cube Grains of Rolled Aluminium

Influence of variation in grain boundary parameters on the evolution of atomic structure and properties of [111] tilt boundaries in Aluminum

EVOLUTION OF LOCAL ORIENTATIONS WITHIN INDIVIDUAL GRAINS IN ROLLED PURE POLYCRYSTALLINE ALUMINUM

First-Principles Study of Physical Properties of (110) Symmetric Small-Angle Tilting Grain Boundary with Full Dislocation in Aluminum

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Slip-induced mechanism of the orientation-dependent deformation banding in cold rolled Al-Mg alloy

Evolution Of Microstructure And Local Crystallographic Orientations In Rolled Al-1%Mn Single Crystals Of {001}< 110 > Orientation

Orientation Dependence of the Deformation Microstructure of Ta-4% W after Cold-Rolling

Evolution of microstructure and local crystallographic orientations in rolled Al 1% Mn single crystals of {l_brace} 0 0 1 {r_brace}< 1 1 0> orientation

Arrangement and Decomposition of Grain Boundary Dislocations: Two-Mode Phase-Field Crystal Simulation

Microstructure–grain Orientation Relationship in Coarse Grain Nickel Cold-Rolled to Large Strain

MICROSTRUCTURAL EVOLUTION OF COLUMNAR GRAIN Al DURING COLD ROLLING II. Mircoscopic Subdivision

Macroscopic Subdivision Of Columnar Grain Aluminium With {001} < U Upsilon 0 > Orientations Following Low Strain Deformation