Abstract:During the fabrication of an indium-gallium-zinc oxide (IGZO) thin film transistor (TFT), the thermal process was used to reduce the resistivity of IGZO. The annealing temperature was found to have great influence on the transistor characteristics. At an optimized heat-treatment temperature, the depletion-mode IGZO TFT was fabricated with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage. And the relatively conductive IGZO could directly replace the indium tin oxide as the transparent electrode of the organic light-emitting diode (OLED), reducing the mask count of the backplane for the active-matrix OLED display. INTRODUCTION Thin film transistor (TFT) based on metal oxide (MO), especially, indium-gallium-zinc oxide (IGZO), is considered as a good candidate to fabricate large area backplane for active-matrix organic light-emitting diode (AMOLED) display, due to its high mobility, good uniformity and low off-state current [1]. Our previous study [2] suggested that the resistivity (ρ) of IGZO highly depended on the heat-treatment conditions, such as annealing ambience, temperature, duration and gas permeability of IGZO cover, while the thermal process was often inevitable during the fabrication of IGZO TFT. With the active layer of IGZO covered with the gas-permeable silicon oxide (SiOx), the TFT was subjected to a serious anneals in an oxygen-deficient nitrogen (N2) ambience. With the increasing temperature, although the mobility was enhanced, the turn-on voltage (Von) became more and more negative. At an optimized temperature, the depletion-mode (DM) IGZO TFT with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage was fabricated. Furthermore, such annealing-induced conductive IGZO source/drain regions can be directly used to replace the indium tin oxide (ITO) as the transparent electrode of OLED, reducing the mask count of AMOLED backplane. Annealing-Induced DM IGZO TFT Shown in Figure 1 is the evolution of the schematic cross-section of an IGZO TFT. A gate dielectric of 100 nm silicon oxide (SiOx) was first thermally grown on an n+ silicon substrate, which served as the gate electrode. 10 or 20 nm IGZO film was then room-temperature sputtered using a target of In2O3:Ga2O3:ZnO = 1:1:1 mol% in an atmosphere of 10% oxygen (O2) and 90% argon (Ar). After the patterning of the active-island using the hydrofluoric acid, a passivation layer of 300 nm SiOx was deposited at 300 oC in a plasma-enhanced chemical vapor deposition (PECVD) reactor. The tetraethylorthosilicate (TEOS) and O2 were used as the source gases. The contact holes were then opened and the resulting structure was subjected to a series of anneals, as shown in Figure 1a. Finally, 300 nm aluminum (Al) was deposited and patterned into electrodes (Fig. 1b). These TFTs were measured using an Agilent 4156C semiconductor parameter analyzer. n+ Si 100nm SiOx 300nm SiOx

Indium Gallium Zinc Oxide - Carbon Nanotube Composite Thin Film Transistor

High-performance Carbon Nanotube/ingazno Composite Thin Film Transistors and Concentration Effect

Fabrication and performance of indium oxide based transparent thin film transistors

A Carbon Nanotube Electrode A-Igzo-Tft

Design and Mechanism of Embedding Specific Carbon Nanotubes in Sputtered Sandwiched InGaZnO Thin-Film Transistors

High mobility amorphous InGaZnO thin film transistor with single wall carbon nanotubes enhanced-current path

Crystalline InGaZnO quaternary nanowires with superlattice structure for high-performance thin-film transistors

Indium–gallium–zinc–oxide thin-film transistors: Materials, devices, and applications

Fabrication and Properties of InGaZnO Thin-Film Transistors Based on a Sol–Gel Method with Different Electrode Patterns

Indium–gallium–zinc–oxide Thin-Film Transistors:Materials,devices, and Applications

Performance of Transparent Indium–Gallium–Zinc Oxide Thin Film Transistor Prepared by All Plasma Enhanced Atomic Layer Deposition

Chemical and Electrical Properties of Low-Temperature Solution-Processed In–Ga–Zn-O Thin-Film Transistors

The Fabrication of Indium–Gallium–Zinc Oxide Sputtering Targets with Various Gallium Contents and Their Applications to Top-Gate Thin-Film Transistors

Characteristics of Elevated-Metal Metal-Oxide Thin-Film Transistors Based on Indium-Tin-Zinc Oxide

Fabrication of Transparent Indium Zinc Oxide Thin Film Transistors by Sol-gel Technology

A-Igzo TFTs with Inductively Coupled Plasma Chemical Vapor Deposited ${\rm SiO}_{x}$ Gate Dielectric

High Performance Indium‐Gallium‐Zinc Oxide Thin Film Transistor via Interface Engineering

Sub-100 Nm Self-Aligned Top-Gate Amorphous InGaZnO Thin-Film Transistors with Gate Insulator of 4 Nm Atomic-Layer-Deposited AlOx

Annealing-Induced Depletion-Mode Indium-Gallium-Zinc Oxide Thin-Film Transistor and Its Application to Active-Matrix Organic Light-Emitting Diode Display

Indium Zinc Oxide Nanosheet Transistor with 2 nm Channel Thickness for Monolithic Three-dimensional Integrated Circuit

Fabrication of Indium-Tin-Oxide Thin-Film Transistor Using Anodization