Abstract:To improve the performance of the cell in terms of current density, power density and byproduct water removal from the cathode, three new cathode flow fields are designed, fabricated and tested. Design-1 is a conventional serpentine with a channel width and rib width of 0.8mm . Design-2 is a-four outlet, and one inlet-four zone serpentine with a channel width and rib width of 0.8mm . Design-3 is a four outlet-one inlet four zone serpentine with a gradually reducing channel width from 1.5mm at the inlet to 0.8mm at the four outlets. Design-4 is a four outlet-one inlet four zone zigzag serpentine with a gradually reducing channel width from 1.5mm at the inlet in the middle to 0.8mm at the four outlets. The open angle of 0.16° is used in design-3 and design-4. All the designs cover a 50mm×50mm area with open ratios in the range 48.9% - 50.0% . To assess the cell's performance, an experimental study is conducted to determine the effect of the new cathode flow field design along with methanol flow rates and methanol concentrations. Electrochemical characterization methods are used to measure the power density of the new fabricated transparent DMFC. Results indicate that the highest recorded limiting current density and peak power density by the experiment are 460mA/cm2 and 50mW/cm2 respectively. The reference design using a conventional serpentine flow field attains a current density of 257mA/cm2 and power density of 24mW/cm2 . Comparing new cathode designs with the reference one, the enhancement percentage in terms of the maximum peak power density by design-2, -3 and -4 are 44% , 107% and 22% , respectively. The lower anode flowrates outperforms the higher flowrates. The byproduct water at the cathode was better removed by the new cathode designs compared to the reference design. This research provides leeway for researchers to enhance the performance of DMFCs via new cathode flow fields.

Experimental Investigations of Anode Structure on the Performance of Air-Breathing Μdmfc

Design, Fabrication and Testing of a Silicon-Based Air-Breathing Micro Direct Methanol Fuel Cell

Experimental Investigations of the Anode Flow Field of A Micro Direct Methanol Fuel Cell

Design, Optimization and Microfabrication of a Micro-Direct Methanol Fuel Cell with Microblocks in Anode Structure

A Silicon-Based Micro Direct Methanol Fuel Cell with Microblocks in Anode Structure

An Air-Breathing Micro Direct Methanol Fuel Cell with 3D KOH-Etched Cathode Structure

An Air-Breathing Micro Direct Methanol Fuel Cell Stack Employing a Single Shared Anode Using Silicon Microfabrication Technologies

A Water Collecting and Recycling Structure for Silicon-Based Micro Direct Methanol Fuel Cells

Parameters research of the anode flow field of a micro direct methanol fuel cell

A model investigation of the performance of a novel anode flow-field structure with microblocks for micro direct methanol fuel cells

Design and fabrication of a silicon-based micro direct methanol fuel cell stack

Modeling study of an air‐breathing micro direct methanol fuel cell with an extended anode catalyst region

Influence of Current Collector Design and Combination on the Performance of Passive Direct Methanol Fuel Cells

Design and Fabrication of a Polymer-Based Micro Direct Methanol Fuel Cell

A Monolithic Integrated Micro Direct Methanol Fuel Cell Based on Sulfo Functionalized Porous Silicon

Optimization of Membrane Electrode Assembly in Air-Breathing Direct Methanol Fuel Cell

Development of MEMS-based direct methanol fuel cell with high power density using nanoimprint technology

A Neat Methanol Fed Passive DMFC with a New Anode Structure

Enhancing the performance of direct methanol fuel cells using new cathode flow field designs: An experimental investigation

A Study of the Direct Dimethyl Ether Fuel Cell Using Alkaline Anolyte

Capillary-based Water Removal Cathode for an Air-Breathing Micro Direct Methanol Fuel Cell