Abstract:Micro-interconnection copper pillar bumps are being widely used in the packaging areas of memory chip and high performance computer due to their high density, good conductivity and low noise. Studying the interfacial behavior of copper pillar bump is of great significance for understanding its failure mechanism and microstructure evolution in order to improve the reliability of flip chip package. The thermoelectric stress test, in-situ monitor, infrared thermography test, and microstructure analysis method are employed to study the interfacial reaction, life distribution, failure mechanism and their effect factors of Cu/Ni/SnAg1.8/Cu flip chip copper pillar interconnects under 9 groups of thermoelectric stresses including 2104-3104 A/cm2 and 100-150°C. Under thermoelectric stresses, the interfacial reaction of Cu pillar can be divided into three stages:Cu6Sn5 growth and Sn solder exhaustion; the Cu6Sn5 phase transformation, exhaustion and the Cu3Sn phase growth; voids formation and crack propagation. The rate of Cu6Sn5 phase transforming into Cu3Sn phase is positively correlated with the current density. There are four kinds of failure modes including Cu pad consumption, solder complete consumption and transformation into Cu3Sn, Ni plating layer erosion and strip voids. An obvious polar effect is observed during the dissolution of Cu pads on the substrate side and the Ni layer on the Cu pillar side. When Cu pad is located at the cathode, the direction of electron flow is the same as that of the heat flow, and it can accelerate the consumption of Cu pad and the growth of Cu3Sn. When Ni layer serves as the cathode, the electron flow can enhance the consumption of Ni layer. Under 150°C and 2.5104 A/cm2, the local Ni barrier layer is eroded after 2.5 h, which results in the transformation of Cu pillar on the Ni side into (Cux, Niy)6Sn5 and Cu3Sn alloy. The life of Cu pillar interconnection complies well to the 2-parameter Weibull distribution with a shape parameter of 7.78, which is a typical characteristic of cumulative wear-out failure. The results show that the intermitallic growth behavior and failure mechanism at Cu pillar interconnects are significantly accelerated and changed under thermoelectric stresses compared with the scenario under the single high temperature stress.

The Study on the Shaping of Electroplated Copper Pillar Bumping

Influence of Electroplating Current Density on Through Silicon Via Filling

Effect of leveler on microstructure and stress of electroplated copper for TSV application

Potential-Dependence Of Additives Distribution In Copper Electrodeposition Via Filling

Method to Improve the Process Efficiency for Copper Pillar Electroplating

Cu Pillar Electroplating Using a Synthetic Polyquaterntum Leveler and Its Coupling Effect on SAC305/Cu Solder Joint Voiding

Effect of Different Material Systems on Interconnection Properties of 30μm Pitch Micro Bumps

Top Metal Layer Electro Plating Edge Bevel Removal Improvement Study

Novel design and reliability assessment of a 3D DRAM stacking based on Cu-Sn micro-bump bonding and TSV interconnection technology

Promotion of High-Speed Copper-Filling Performance for Interconnections with Increasing Aspect-Ratio Using Compound Additives

Electroplated Copper Additives for Advanced Packaging: A Review

Compound additives and stress study of EDTA-2Na chemical copper plating system in printed circuit boards

Optimization of High-Speed Electrolytic Plating of Copper Pillar to Achieve a Flat Top Morphology and Height Uniformity

Understanding Effect of Additives in Copper Electroplating Filling for Through Silicon Via

Influence of PUB2 on the Leveling Effect of Chip Copper Connection Electroplating: Mechanism and Applications

Study on Chemical Activity of Electroless Copper Plating

Characterization of sintered Cu nanopaste for micro-bumping with Injection Molded Solder technology

Reliability Study of Fine Pitch Cu-Sn Micro-Bump Structure Electromigration Test by Finite Element Simulation

Interfacial reaction and failure mechanism of Cu/Ni/SnAg1.8/Cu flip chip Cu pillar bump under thermoelectric stresses

A Study on Improvement and Extension of Fine-Pitch Micro-Bump Interconnects Technology: New Metallurgy & Flux-Less Oxide-removal Laser Assembly (FLOLA)

A High Copper Concentration Copper-Quadrol Complex Electroless Solution for Chip Bonding Applications