Abstract:Micro-interconnection copper pillar bumps are being widely used in the packaging areas of memory chip and high performance computer due to their high density, good conductivity and low noise. Studying the interfacial behavior of copper pillar bump is of great significance for understanding its failure mechanism and microstructure evolution in order to improve the reliability of flip chip package. The thermoelectric stress test, in-situ monitor, infrared thermography test, and microstructure analysis method are employed to study the interfacial reaction, life distribution, failure mechanism and their effect factors of Cu/Ni/SnAg1.8/Cu flip chip copper pillar interconnects under 9 groups of thermoelectric stresses including 2104-3104 A/cm2 and 100-150°C. Under thermoelectric stresses, the interfacial reaction of Cu pillar can be divided into three stages:Cu6Sn5 growth and Sn solder exhaustion; the Cu6Sn5 phase transformation, exhaustion and the Cu3Sn phase growth; voids formation and crack propagation. The rate of Cu6Sn5 phase transforming into Cu3Sn phase is positively correlated with the current density. There are four kinds of failure modes including Cu pad consumption, solder complete consumption and transformation into Cu3Sn, Ni plating layer erosion and strip voids. An obvious polar effect is observed during the dissolution of Cu pads on the substrate side and the Ni layer on the Cu pillar side. When Cu pad is located at the cathode, the direction of electron flow is the same as that of the heat flow, and it can accelerate the consumption of Cu pad and the growth of Cu3Sn. When Ni layer serves as the cathode, the electron flow can enhance the consumption of Ni layer. Under 150°C and 2.5104 A/cm2, the local Ni barrier layer is eroded after 2.5 h, which results in the transformation of Cu pillar on the Ni side into (Cux, Niy)6Sn5 and Cu3Sn alloy. The life of Cu pillar interconnection complies well to the 2-parameter Weibull distribution with a shape parameter of 7.78, which is a typical characteristic of cumulative wear-out failure. The results show that the intermitallic growth behavior and failure mechanism at Cu pillar interconnects are significantly accelerated and changed under thermoelectric stresses compared with the scenario under the single high temperature stress.

Reliability Study of Fine Pitch Cu-Sn Micro-Bump Structure Electromigration Test by Finite Element Simulation

Computational Analysis of Mechanical and Electromigration Reliability Problems

A new prediction methodology for electromigration-induced solder degradation in a WL-CSP system

The Study of the Reliability of Complex Components during the Electromigration Process

Comparison of the Time-Dependent Physical Processes in the Electromigration of Deep Submicron Copper and Aluminum Interconnects

Electromigration Reliability of Cu3Sn Microbumps for 3D Heterogeneous Integration

Crystalline Orientation Effect of Single-Grain Sn-Rich Cu Pillar Bumps on Electromigration Lifetime

Understanding the Impact of Surface Engineering, Structure, and Design on Electromigration Through Monte Carlo Simulation and In‐Situ SEM Studies

Novel design and reliability assessment of a 3D DRAM stacking based on Cu-Sn micro-bump bonding and TSV interconnection technology

Effect of Bonding Strength on Electromigration Failure in Cu–Cu Bumps

Mechanical and Electrical Reliability Assessment of Bump-Less Wafer-on-wafer Integration with One-Time Bottom-Up TSV Filling

An in-situ experimental and simulation study on the electromigration behavior of SAC305 solder joints

Reliability Simulation of Metal Bump in A Three-Dimensional Chip Stacking Structure

Experimental and Numerical Studies of Stress Migration in Cu Interconnects Embedded in Different Dielectrics

Experimental and multiphysics simulation study of atoms migration and morphology evolution in solder joints under high current density

Effects of Bonding Parameters on the Reliability of Fine-Pitch Cu/Ni/SnAg Micro-Bump Chip-to-Chip Interconnection for Three-Dimensional Chip Stacking

Numerical Simulation of the Atomic Migration and Diffusion During Current Stressing in the Cu/Sn-58bi/Cu Solder Joints

Interfacial reaction and failure mechanism of Cu/Ni/SnAg1.8/Cu flip chip Cu pillar bump under thermoelectric stresses

The Effect Of Cu Orientation On Fracture Location In Cu3sn-Cu Interface Structure Under Monotonic Loading Condition By Molecular Dynamics Simulation

Effects of Current Stress for Low Temperature Cu/Sn/Cu Solid-State-Diffusion Bonding

Investigation on electromigration failure behavior of SAC305/SnPb micro-hybrid solder joints for package-on-package techniques: Experiment and simulation