Abstract:Cryogenic deep reactive ion etching (Cryo DRIE) of silicon has become an enticing but challenging process utilized in front-end fabrication for the semiconductor industry. This method, compared to the Bosch process, yields vertical etch profiles with smoother sidewalls not subjected to scalloping, which are desired for many microelectromechanical systems (MEMS) applications. Smoother sidewalls enhance electrical contact by ensuring more conformal and uniform sidewall coverage, thereby increasing the effective contact area without altering contact dimensions. The versatility of the Cryo DRIE process allows for customization of the etch profiles by adjusting key process parameters such as table temperature, O2 percentage of the total gas flow rate (O2 + SF6), RF bias power, and process pressure. In this work, we undertake a comprehensive study of the effects of Cryo DRIE process parameters on the trench profiles in the structures used to define cantilevers in MEMS devices. Experiments were performed with an Oxford PlasmaPro 100 Estrelas ICP-RIE system using positive photoresist SPR-955 as a mask material. Our findings demonstrate significant influences on the sidewall angle, etch rate, and trench shape due to these parameter modifications. Varying the table temperature between -80°C and -120°C under a constant process pressure of 10 mTorr changes the etch rate from 3 to 4 μm/min, while sidewall angle changes by ~2°, from positive ( 90° relative to the Si surface) tapering. Altering the O2 flow rate with constant SF6 flow results in a notable 10° shift in sidewall tapering. Furthermore, SPR-955 photoresist masks provide selectivity of 46:1 with respect to Si and facilitates the fabrication of MEMS devices with precise dimension control ranging from 1 to 100 μm for etching depths up to 42 μm using Cryo DRIE. Understanding the influence of each parameter is crucial for optimizing MEMS device fabrication.

A Single Mask Dry Releasing Process for Making High Aspect Ratio Soimemsdevices.

A single-mask dry-release process for fabrication of high aspect ratio SOI MEMS devices

Fabrication of SOI MEMS Inertial Sensors with Dry Releasing Process

Fabrication Challenges and Test Structures for High-Aspect-ratio SOI MEMS Devices with Refilled Electrical Isolation Trenches

Design and fabrication of MEMS devices using the integration of MUMPs, trench-refilled molding, DRIE and bulk silicon etching processes

A New Release Process in Surface Micromachining-Double Mask Technology

A new process for releasing micromechanical structures in surface micromachining with polysilicon support and LPCVD Si3N4 embedded mask

The SOI DAWN process for three-dimensional silicon micromachining and its applications

Fabrication of High Aspect Ratio Muti-Steps on Si by Dry Etching

Single wafer fabrication of a symmetric double-sided beam-mass structure using DRIE and wet etching by a novel vertical sidewall protection technique

Oxide Or Metal Interface Damage Improvement Of Deep Silicon Etch Process By Low Power Rf Of Low Frequency

Methods to Protect Silicon Microstructures from the Damages in Deep Reactive Ion Etching

Hard Mask Free Drie Of Crystalline Si Nanobarrel With 6.7nm Wall Thickness And 50:1 Aspect Ratio

A molded surface-micromachining and bulk etching release (MOSBE) fabrication platform on (1 1 1) Si for MOEMS

Cryogenic DRIE Processes for High-Precision Silicon Etching in MEMS Applications

Post-CMOS Process for High-Aspect-ratio Monolithically Integrated Single Crystal Silicon Microstructures

Wafer level bulk titanium ICP etching using SU8 as an etching mask

An SOI-based post-fabrication process for compliant MEMS devices

Modeling and Simulation of Silicon Dry Etching

A CMOS Compatible Process for Monolithic Integration of High-Aspect-ratio Bulk Silicon Microstructures

Bulk Micromachining Fabrication Platform Using the Integration of DRIE and Wet Anisotropic Etching