Abstract:Hot embossing is a cost-effective and flexible fabrication technology with high replication accuracy for feature sizes as small as 50 nm. Here we develop a reinforced polydimethylsiloxane (PDMS) mold for hot embossing of cyclic olefin polymer (COP) sheets in the fabrication of microfluidic chips and demonstrate the method by fabricating chips for automated sample digitization in digital nucleic acid assays. The PDMS is hardened by adding an investment powder as a dopant and is constrained with an aluminum frame to prevent lateral expansion during hot pressing. The reinforced PDMS mold demonstrated excellent performance in hot embossing (180 °C, 103 kPa, 5 min) for micropatterning COP sheets, with highly reproducible features as small as 10 μm (width of draining channel). In contrast, the microscale features were inconsistent and distorted when omitting either the investment powder or frame from the PDMS mold. COP chips were assembled by thermally bonding patterned and unpatterned COP sheets. We tested the performance of the COP chip for automated sample digitization in a digital LAMP assay used to quantify human papillomavirus-18 (HPV-18) DNA. A mixture of nucleic acid amplification reagents was loaded into the main channel of the chip using a syringe pump, then the solution was spontaneously partitioned into chambers (∼0.6 nL), which were then isolated by flowing oil through the chip. The digital LAMP assay produced accurately absolute quantitation of DNA at concentrations ranging from 10 to 1000 copies per μL. The strategy presented here provides a simple, low-cost method to prepare molds for hot embossing, which facilitates rapid validation of microfluidic designs.

The microfluidic chip fabricated by Hot Embossing Lithography for single- microsphere test

Experimental Study on the Hot Embossing Polymer Microfluidic Chip

Fabrication Of Microfluidic Chip And Its Application

Fabrication of Fluidic Chips with 1-D Nanochannels on PMMA Substrates by Photoresist-Free UV-lithography and UV-assisted Low-Temperature Bonding

Design and Fabrication of Micro Hot Embossing Mold for Microfluidic Chip Used in Flow Cytometry

A Low-Cost Method of Fabricating Hybrid Micro-Nano Fluidic Chip by Double-Layer PDMS Mold and UV–thermal Nanoimprinting

Fabrication of Micro/Nanofluidic Chip on Glass Substrate and Its Application for Electrokinetic Concentration of Proteins

Fabrication of Microfluidic Focusing Chip for Bioinstrumentation

A Reinforced PDMS Mold for Hot Embossing of Cyclic Olefin Polymer in the Fabrication of Microfluidic Chips.

Novel Fabrication Technology Of Polydimethylsiloxane Microfluidic Chip

A Simple and Low-Cost Method for Fabrication of Polydimethylsiloxane Microfludic Chips.

Fabrication of Microfluidic Chips Based on an EHD-Assisted Direct Printing Method

Novel polydimethylsiloxane (PDMS) based microchannel fabrication method for lab-on-a-chip application

Fabrication of Poly(methyl Methacrylate)(pmma) Microfluidic Chips by a Simple Hot Embossing Method

Fabrication Of Microfluidic Chips By An Ultrasonic Micromachining With Wet-Etch Smoothing Method On Glass Substrates

Fabrication of PDMS Microfluidic Chips Used in Rapid Diagnosis by Micro Jetting

Design and fabrication of a microfluidic detection chip

Investigation of hot roller embossing for microfluidic devices

Fabrication of a Three-Layer PDMS Pneumatic Microfluidic Chip for Micro Liquid Sample Operation

Fabrication of PDMS Microfluidic Chip Used in Ultraviolet Integrated Biological Chip

Rapid Fabrication of Plastic Microfluidic Channels Using PDMS As Hot Embossing Tools