Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

Synthesis of aluminum-doped mesoporous zirconia with improved thermal stability

The Effect of Al2O3 on the Thermal Stability and Mechanical Properties of 3Y-TZP

Effect of Ce–Zr Mixed Oxides on the Thermal Stability of Transition Aluminas at Elevated Temperature

Synthesis and Characterization of Yttria-Doped Mesoporous Zirconia

Sintering Behavior and Mechanical Properties of Alumina-Coated Zirconia Ceramics

Microstructure and phase transformation behavior of Al2O3–ZrO2 under microwave sintering

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Optimisation on the stability of CaO-doped partially stabilised zirconia by microwave heating

Effects of Zircon Additive on the Properties of 95-Alumina Ceramic

Role of t-ZrO2 stabilization methods in phase composition, structure and properties of ZTA ceramics

Study of microstructure, electronic structure and thermal properties of Al2O3-doped tetragonal YSZ coatings

The Study on Degradation of Y<sub>2</sub>O<sub>3</sub>-CeO<sub>2</sub>-Partially Stabilized ZrO<sub>2</sub> Adding Al<sub>2</sub>O<sub>3</sub> Particles at Low Temperature

Effect of Dy2O3 content on microstructure and mechanical properties of zirconia-toughened alumina

Preparation and Thermal Stability of Zirconia-Doped Mullite Fibers Via Sol-Gel Method

Optimization of the structure and morphology of monoclinic phase nanoscale zirconium dioxide

Grain boundary segregation for enhancing the thermal stability of alumina-mullite diphasic fibers by La2O3 addition

Effect of Al2O3 on the Phase Stability of Y-Ce-TZP/Al2O3 Composites at Low Temperature

Improved Catalytic Activity and Stability of Mesostructured Sulfated Zirconia by Al Promoter

Effects of Zr on the Precursor Architecture and High-Temperature Nanostructure Evolution of Sioc Polymer-Derived Ceramics

Microstructure and mechanical properties of dense ZTA ceramics with high Cr2O3 solution

Effect of zirconia sol on the microstructure and properties of Al2O3-based ceramic fabricated from natural bauxite