Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

Preparation and Thermal Stability of Zirconia-Doped Mullite Fibers Via Sol-Gel Method

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Structure evolution and thermal stability of La_2O_3-doped mullite fibers via sol-gel method

Preparation of Mullite Fibers by Sol-Gel Process and Study of Their Morphology

Preparation And High-Temperature Strengthening Of Tetragonal Zirconia Mullite Whisker Composites

Zirconia-alumina multiphase ceramic fibers with exceptional thermal stability by melt-spinning from solid ceramic precursor

The Effect of ZrO2Fiber on the Flexural Toughness and Thermal Shock Resistance of the Mullite-10%vol.SiC Whisker Ceramic

Oxidation Protection of Carbon Fiber by Sol-Gel Derived Boron Doped Yttria Stabilized Zirconia Coatings

Preparation of Zirconia Powders by Sol-gel Process

Mullite Fiber Prepared by Sol-Gel Method Using Low-Molecular-Weight Acids as Modifying Agents

Grain boundary segregation for enhancing the thermal stability of alumina-mullite diphasic fibers by La2O3 addition

Preparation and Application of Spinnable Zirconium Sol I.Preparation of Continuous Zirconia Fiber

Thermal decomposition and reaction sintering for synthesis of mullite-zirconia composite using kaolin, γ-alumina and zirconia

Reaction mechanisms and properties of in situ porous Al2O3-ZrO2-mullite composites

Effect of silica sol on phase transition of alumina-mullite fibers

Synthesis of Monolithic Zirconia with Macroporous Bicontinuous Structure Via Epoxide-Driven Sol–gel Process Accompanied by Phase Separation

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Reaction sintering of ZrSiO4/α-Al2O3 mixed powders with Y2O3 addition

Synergistic regulation of temperature resistance and thermal insulation performance of zirconia-based ceramic fibers

Preparation of mullite ceramics with equiaxial grains from powders synthesized by the sol-gel method

EFFECTS OF ZIRCONIA SOL ON THE PROPERTIES OF CORUNDUM -MULLITE DUPLEX CERAMICS