Abstract:Lead zirconate titanate (PZT)-based ferroelectric ceramic materials are piezoelectric materials of commercial importance. Strontium zirconate titanate (SZT) perovskite materials also have a wide application area. PZ and SZT starting solutions can be prepared using a variety of suitable methods. Among these methods, the sol-gel process has attracted special attention due to the low temperature requirement, homogeneity and the ability to obtain the appropriate particle size. The electrospinning method is the most effective and widely used method in nanofiber production. Electro-spinning is a method that enables the production of solid and hollow nanofibers in long lengths, homogeneous diameters and various compositions. When the electro-spinning technology is combined with the sol-gel method, continuous nanofibers, nanotubes and filled nanofibers are produced from polymer or ceramic solution under a certain electric field. In this study, lead zirconate titanate (PZT) and strontium zirconate titanate (SZT) solutions containing Sr and Pb were prepared by sol-gel method. Solutions were prepared using metal salts and alkoxides as the precursor materials. The solutions obtained were fed at flow rates of 1.6, 1.8, 2.0 mL / hour and PZT and SZT nanofibers were formed by electrospinning method at 20 kV voltage rating. Different parameters of the electrospinning device were examined and the SZT and PZT nanofibers were produced with optimum properties. Crystal structure, characterization of morphological surface and chemical properties of the produced nanofibers were done with XRD, SEM and EDX, respectively. XRD results showed that the perovskite structure of PZT and SZT was not damaged during Sol-gel and electrospinning processes. A small amount of beady structure was observed in SEM analysis of PZT and SZT nanofibers. According to EDX analysis of nanofibers, it was observed that the PZT and SZT structure was also formed.

Preparation and Application of Spinnable Zirconium Sol I.Preparation of Continuous Zirconia Fiber

Electrospun zirconia nanofibers and corresponding formation mechanism study

A General Propylene Epoxide-assisted Sol-Gel Route for the Synthesis of ZrO2-SnO2 Composite Sols

Preparation and Thermal Stability of Zirconia-Doped Mullite Fibers Via Sol-Gel Method

Preparation and Characterization of 8mol％ Yttria-stabilized ZrO2 (8YSZ) Fibers Prepared by Sol-Gel Method

Preparation of Zirconia Powders by Sol-gel Process

Preparation of high-strength alumina-zirconia fibers by the sol-gel method combined with two-step sintering processes

Effect of Heat-treatment Atmosphere on Preparation of Continuous Zirconia Fibers

Fabrication of High‐Strength Continuous Zirconia Fibers and Their Formation Mechanism Study

Preparation of Zinc Oxide Nanofibers by Electrospinning

Synthesis of Monolithic Zirconia with Macroporous Bicontinuous Structure Via Epoxide-Driven Sol–gel Process Accompanied by Phase Separation

The characteristics of spinnable mullite sol prepared by sol-gel method

Continuous Sol–Gel Coating of Ceramic Multifilaments: Evaluation of Fiber Bridging by Three‐Point Bending Test

Preparation of YIG Single Crystal Nanofibers Via an Electrospinning Technique

Rheologic behaviors and continuously dry spinning of polyacetylacetonatozirconium fibers

Preparation and Characterization of Sc2o3-Doped Zro2 Nanofiber

Preparation and Characterization of PbO.ZrO2.TiO2 and SrO.ZrO2.TiO2 Nanofibers by Electrospinning Method

Oxidation Protection of Carbon Fiber by Sol-Gel Derived Boron Doped Yttria Stabilized Zirconia Coatings

Research Development for the Fabrication of Inorganic Continuous Mullite Fiber

Preparation of Continuous Aluminum Oxide Fibers with Silicon Oxide and Zirconium Oxide Additives

Preparation of Ultrafine Zirconia Suspension for Gelcasting