Abstract:Two compositions Ce0.50Zr0.39La0.04Y0.07O2−δ and Ce0.25Zr0.65La0.04Y0.06O2−δ based on ceria-zirconia solid solutions were prepared as nanopowders using a continuous hydrothermal flow synthesis reactor, followed by either freeze-drying or hotplate-drying of the slurry. Each dried nanopowder was then subjected to 10h heat-treatment at 1000°C, 1100°C or 1200°C in air (to simulate accelerated ageing). The reducibility and hydrogen consumption of the oxidised samples were measured using temperature programmed reduction (TPR) up to 1000°C. The effects of composition, drying method and heat-treatment temperature were evaluated on the TPR profiles of the materials. The powders were further investigated using a range of analytical methods including UV/Vis spectroscopy (which yielded colour data), Raman spectroscopy, powder X-ray diffraction, BET surface area measurements and X-ray photoelectron spectroscopy (XPS). Chemometric methods were used to investigate relationships between the spectroscopic and total oxygen storage capacity (OSC) data. Principal component analysis (PCA) was used to provide a simple interpretation of the effects of various synthesis and treatment parameters on Raman spectra. Principal component regression (PCR) was used to build regression models relating the Raman spectra and the temperature of hydrogen consumption peak at several set temperatures in the TPR. The total hydrogen consumption of the materials was generally high, while the drying and heat-treatment conditions appeared to have a significant effect on the final properties of the resulting powders, such as the surface area and total oxygen storage capacity.

Effects of Zr on the Precursor Architecture and High-Temperature Nanostructure Evolution of Sioc Polymer-Derived Ceramics

Effect of Zr on the Microstructure and High-Temperature Phase Separation Evolution of SiOC Aerogels

Effect of Si/Zr molar ratio on the sintering and crystallization behavior of zircon ceramics

Microstructure and phase evolution behavior of SiZrBC ceramic precursors synthesized via sol–gel method

Synthesis and Characterization of Doped Nano-Sized Ceria–zirconia Solid Solutions

Effect of annealing temperature on the microstructure, dielectric, and microwave absorption performance of precursor blends derived ZrSiOCN ceramics

High Temperature Structure Evolution of Macroporous SiOC Ceramics Prepared by a Sol–gel Method

Effect of ZrB2 on promoting the phase transformation mechanism of Si3N4-based ceramics at low temperature

Effect of ZrB2 and its oxide impurities (ZrO2 and B2O3) on hot-pressed Si3N4 ceramics at low temperature

Effect of Zr2Al4C5 Content on the Mechanical Properties and Oxidation Behavior of ZrB2-SiC-Zr2Al4C5 Ceramics

Effects of SDBS and ZrO2 additives on the microstructure and properties of silicon-bonded SiC porous ceramics

Effect of ZrB2 powders on densification, microstructure, mechanical properties and thermal conductivity of ZrB2-SiC ceramics

Influences of preparation parameters on the structural and catalytic performance of zirconia in isosynthesis

Effect of HF and NaOH Etching on Chemical and Structure Stability of Hollow SiOC Ceramics

Effects of ZrSiO4 content on properties of SiO2-based ceramics prepared by digital light processing

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating

Sol-gel preparation of ZrO2–Li2Si2O5 ceramics and their sintering properties

Isothermal Oxidation of Zr2[Al(Si)]4C5–SiC Composites at 1000–1300°C in Air

Temperature‐dependent mechanical and oxidation behavior of in‐situ formed ZrN/ZrO2‐containing Si3N4‐based composite

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics