Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

Synthesis and Characterization of Yttria-Doped Mesoporous Zirconia

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Preparation and Characterization of Mesoporous Zirconia Materials by Self-Assembly Method

Synthesis of Monolithic Zirconia with Macroporous Bicontinuous Structure Via Epoxide-Driven Sol–gel Process Accompanied by Phase Separation

Mesoporous Yttria-Zirconia Solid Solution with Improved Textural Properties Prepared Via Lauric Acid-Assisted Synthesis

Study of Factors Influencing the Microstructure and Phase Content of Ultrafine Y-Tzp

Synthesis and Characterization of Mesoporous Zirconia Molecular Sieve

Controlled sintering and phase transformation of yttria-doped tetragonal zirconia polycrystal material

Hydrothermal Synthesis and Characterization of Zirconia Nanocrystallites

Synthesis of yttria-stabilized zirconia powders for plasma spray by internal gelation

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Preparations and Characterizations of New Mesoporous ZrO2 and Y2O3-stabilized ZrO2 Spherical Powders

Fabrication and Properties of Porous Yttria-Stabilized Zirconia Ceramics

Synthesis of aluminum-doped mesoporous zirconia with improved thermal stability

Crystal phase study of stabilized zirconia collected by dust catcher during airflow pulverization

Preparation and characterization of yttria stabilized zirconia nanoarrays

An EXAFS Study of the Nanocrystalline Transformation of ZrO2:Y2O3(5%)

Synthesis and Characterization of Thermally Stable Mesostructured Sulfated Zirconia by a Novel Sulfate-Assisted Alcohothermal Route

Raman and X-ray photoelectron spectroscopic characterizations of thermal stability of 3 mol% yttria stabilized zirconia ceramics

Influence of Y2O3 Doping on Phase Evolution and Dielectric Characteristics of ZrO2 Ceramics