Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

Crystal phase study of stabilized zirconia collected by dust catcher during airflow pulverization

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Formation and Rate Processes of Y[sub 2]o[sub 3] Stabilized ZrO[sub 2] Thin Films from Zr(DPM)[sub 4] and Y(DPM)[sub 3] by Cold-Wall Aerosol-Assisted MOCVD

Formation and Rate Processes of Y2o3 Stabilized Zro2 Thin Films from Zr(Dpm)(4) and Y(Dpm)(3) by Cold-Wall Aerosol-Assisted Mocvd

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Fabrication of Submicron Tetragonal Polycrystalline ZrO2 by the Transformation of Micro Monoclinic ZrO2 under High Pressure

Controlled sintering and phase transformation of yttria-doped tetragonal zirconia polycrystal material

Fabrication of Pure T′ Phase YSZ Ceramics by Spark Plasma Sintering

Synthesis of yttria-stabilized zirconia powders for plasma spray by internal gelation

Study of Factors Influencing the Microstructure and Phase Content of Ultrafine Y-Tzp

Modeling Microstructure Formation in Yttria-Stabilized Zirconia (YSZ) Droplet with High Impact Velocity in Supersonic Plasma Spray

Study on the process and properties of nano-sized polycrystal zirconia powders by co-precipitation in super-alkaline medium

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Preparation and properties of yttria-stabilized tetragonal phase zirconia nano-ceramics by high gravity

From zirconia to yttria: Sampling the YSZ phase diagram using sputter-deposited thin films

An EXAFS Study of the Nanocrystalline Transformation of ZrO2:Y2O3(5%)

Zro2 and Ysz Thin-Films Synthesized by Microwave Plasma Cvd Process

Influence of Y2O3 Doping on Phase Evolution and Dielectric Characteristics of ZrO2 Ceramics

Preparation of epitaxial yttria-stabilized zirconia with non-quilibrium t' phase and ferroelastic domain by pulsed laser deposition

Phase Transformation Behavior in Air Plasma Sprayed Yttria Stabilized Zirconia Coating

Structural evolution and phase transformation behaviors of 10 wt. % dysprosia stabilized zirconia ceramic powders