Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

From zirconia to yttria: Sampling the YSZ phase diagram using sputter-deposited thin films

Formation and Rate Processes of Y2o3 Stabilized Zro2 Thin Films from Zr(Dpm)(4) and Y(Dpm)(3) by Cold-Wall Aerosol-Assisted Mocvd

Formation and Rate Processes of Y[sub 2]o[sub 3] Stabilized ZrO[sub 2] Thin Films from Zr(DPM)[sub 4] and Y(DPM)[sub 3] by Cold-Wall Aerosol-Assisted MOCVD

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Deposition of Y2O3 stabilized ZrO2 thin films from Zr(DPM)4 and Y(DPM)3 by aerosol-assisted MOCVD

Cubic Yttria Stabilized Zirconia Sintering Additive Impacts: A Comparative Study

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Structural and compositional characterization of yttria-stabilized zirconia: evidence of surface-stabilized, low-valence metal species

Zro2 and Ysz Thin-Films Synthesized by Microwave Plasma Cvd Process

Deposition and Characterization of YSZ Thin Films by Aerosol-Assisted CVD

Preparation of epitaxial yttria-stabilized zirconia with non-quilibrium t' phase and ferroelastic domain by pulsed laser deposition

Few-monolayer yttria-doped zirconia films: Segregation and phase stabilization

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Microscopic Mapping of Dopant Content and Its Link to the Structural and Thermal Stability of Yttria-Stabilized Zirconia Polycrystals

Yttria-stabilized zirconia (8YSZ) synthesis in a supercritical CO 2 -assisted process: a parametric study for achieving cubic phase stability

Critical evaluations on the crystallographic properties of translucent dental zirconia ceramics stabilized with 3-6 mol% yttria

Influence of Y2O3 Doping on Phase Evolution and Dielectric Characteristics of ZrO2 Ceramics

Additive manufacturing of 3D yttria-stabilized zirconia microarchitectures

Preparation, Thermophysical Properties, and Thermal Shock Resistance of Yb2O3-doped YSZ Coatings

Deposition of Surface-Melted YSZ Particles by Flame Spraying

Quantification of Yttria in Stabilized Zirconia by Raman Spectroscopy