Abstract:C/Cx-SiCy composites are one of the most promising counterparts of C/C composites as they maintain the mechanical strength of C/C composites while providing excellent anti-ablation properties at the same time. This paper reports that the composites could exhibit even better anti ablation properties after heat treatment. The materials were heat-treated and then tested with a thin-blade oxyacetylene torch without the protection of any coatings. The 1600 °C heat-treated thin-blade specimen could sustain the ablation of the oxyacetylene torch with a temperature of 1776 °C (80 °C higher than the original material without heat treatment) and a lower liner ablation rate (1.31 μm/s) than the original material (1.66 μm/s). An extreme ablation test was also conducted at around 2400 °C, and the 1600 °C heat-treated specimen exhibited a lower linear ablation rate (13 μm/s) than the original specimen (47 μm/s). The influence of the heat treatment on the crystallinity of the matrix is studied with the additional help of Raman spectroscopy and XPS. The ablation mechanism is discussed in detail, and the fluent condition of the thin-blade specimen is simulated. The paper also reports a different ablation behavior of the 1600 °C heat-treated specimen from the material without heat treatment to explain their excellent ablation property.

Effect of surface ablation products on the ablation resistance of C/C-SiC composites under oxyacetylene torch

Cyclic ablation behavior of C/C–ZrC–SiC composites under oxyacetylene torch

Ceramic Matrix Composite Cyclic Ablation Behavior under Oxyacetylene Torch

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Cyclic ablation behavior and microstructure evolution of multi-layer coating on C/C composites under oxyacetylene torch

Ablation behavior of mullite modified C/C-SiC-HfC composites under oxyacetylene torch for single and cyclic ablations with two heat fluxes

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Ablation behavior of thin-blade co-deposited C/Cx-SiCy composites under the influence of the complex fluid conditions of the oxyacetylene torch

Ablation behavior of sharp leading-edge C/C-ZrC-SiC composites using 3000 C oxyacetylene torch

Comparison of the ablation resistance of mullite modified C/C-SiC-HfC and C/C-SiC-HfC composites under oxyacetylene flame of 2.38 MW/m 2 heat flux

Ablation behaviour of the CVD-(ZrC/SiC)3 alternate coating on C/C composites under oxyacetylene torch with different heat fluxes

Ablation behavior of C f /ZrC–SiC ultra–high temperature ceramic composites in oxyacetylene torch and plasma wind tunnel

Ablation performance of C/C-ZrC-SiC composites with in-situ YSi 2 -doped ZrC-SiC-ZrSi 2 coating under oxyacetylene torch

Ablation behaviors of ultra-high temperature ceramic composites

Long-term and cyclic ablation behavior of La2O3 modified Cf/ZrB2-SiC composites at 2500 °C

Ablation and mechanical behaviour of C/C composites under an oxyacetylene flame and tensile loading environment

The influence of heat treatment on the ablation behavior of the C/Cx-SiCy composites tested by thin-blade under oxyacetylene torch

Cyclic Ablation Properties of C/SiC-ZrC Composites

Effect of loading spectrum with different single pulsing time on the cyclic ablation of C/C-SiC-ZrB2-ZrC composites in plasma

Effect of tantalum carbide on the ablation behaviors of hafnium carbide coating for C/C composites under single and cyclic oxyacetylene torch environments

Cyclic ablation behavior of mullite-modified C/C-HfC-SiC composites under an oxyacetylene flame at about 2400 °C