Jitter Measurement Method for Multi-level Disc Based on Interpolation Algorithm

Hu Junhua,Pei Jing,Pan Longfa

DOI: https://doi.org/10.1364/iont.2012.if4a.13

2012-01-01

Abstract:A new jitter measurement method for multi-level disc is presented in this paper combining pulse counting method and interpolation algorithm. The maximum measurement error of jitter is only 0.517% of period of channel clock (T).

What problem does this paper attempt to address?

Jitter Measurement Method for Multi-Level Disc Based on Quadratic Interpolation Algorithm

Junhua Hu,Jing Pei,Longfa Pan

DOI: https://doi.org/10.1117/12.2014726

2013-01-01

Abstract:A new jitter measurement method for multi-level discs is presented in this paper. This method, with merits such as high precision, flexible and low cost, combines the traditional pulse counting method and interpolation algorithm. The principle of this method is explained in detail, and its precision is analyzed. The analysis result is shown to be very effective. It has a broad application prospect and practical value in quality evaluation of multi-level discs.
Design on Measurement System for Jitter of High-speed Optical Disc

谢登科,齐国生,徐端颐,张启程

DOI: https://doi.org/10.3321/j.issn:1005-0086.2004.03.007

2004-01-01

Abstract:A novel system was designed to measure jitter of high-speed optical disc.based on counter method and edge sense technology.Maximum error is only 504 ps and maximum speed is up to 32 x speed.Implemented in FPGA,the system has merits such as simple structure,high precision,low cost and short test time.There is an important use value in quality evaluation of optical disk as an elegant alternative to the time-interval analyzer(TIA).
Jitter testing technology of high-speed optical disc

徐端颐,谢登科

2005-01-01

Abstract:The jitter testing technology for high-speed optical disk was described in this paper. It is based on analysis of the jitter specification of high-speed optical disk. The principle of the system is the novel method of Two-Step Cascading Delay Line. The system was implemented using a single FPGA chip and VHDL programming language which has a character of high resolution, high reliability, compact architecture, simple operation and low cost. The testing results indicate that the system has internal jitter of 40 ps or lower with a single-shot resolution of 75ps and a multi-shot resolution of 5ps, and the system can be applied for jitter analysis of CD at a maximum speed of60X and DVD at 12X.
Analysis And Study On Measurement Of Jitter And Its Precision

Lj Ma,Dy Xu,Lf Pan

DOI: https://doi.org/10.1117/12.416855

2000-01-01

Abstract:Jitter is defined by the variation of each pit length and timing variations between data and clock frequency on discs. As a comprehensive item, it relates with error rate directly. In this paper, the definition, determined and influence factors of jitter n are analyzed. According to the analysis, measurement methods of jitter are provided. The precision of a method. The method's precision and demand are calculated and explained in detail.
Counter-Set Based PCR Jitter Correction Method for DVB-T System

Xi Peng,Jingtao Song,Kuang Wang

DOI: https://doi.org/10.1109/wicom.2007.730

2007-01-01

Abstract:DVB-T is a popular digital video broadcasting standard for wireless digital terrestrial television implementation. Program clock reference, PCR in short, is an important time stamp in DVB-T transport stream. The reason PCR jitter based on DVB-T standard is analyzed and some methods for PCR jitter correction are described and compared. A new method to correct PCR is presented, named as Counter-Set. The principle and system implementation for the method are discussed, and this method is compared with original ones for PCR jitter correction. Counter-Set method and Compensation method are implemented based on FPGA. Results are presented and compared. We get the conclusion that the new method greatly reduces the use of logic units, so it is more efficient than the original one.
Threshold-optimized Dithering Technique for High-quality 3D Shape Measurement

Meng Sen-sen,Cai Ning,Lin Bin

DOI: https://doi.org/10.3788/gzxb20194808.0812002

2019-01-01

Abstract:In order to solve the problem that for defocus binary coding technique, the higher harmonic components in the fringe pattern cause measurement errors, a method of generating a binary image by threshold optimization dithering algorithm is proposed. By introducing the parameter gamma to dynamically adjust the threshold, and considering the influence of different pixel gray values of the image on the dithering algorithm, the sinusoidality of the dithered image stripe after defocusing is improved. Simulation and experiments show that using the threshold optimization dithering algorithm, the fringe after defocusing has better sinusoidality when the parameter gamma is 50. Compared with the traditional Floyd-Steinberg dithering algorithm, the root mean square error can be reduced by 0.013 7 rad when the fringe period is 40 pixel. The imaging is more clear for the sag of the model, and the image quality of the surface reduction of the object is significantly improved.
High-Quality Three-Dimensional Shape Measurement Based on Binary Particle Swarm Dithering Optimization

Cai Ning,Chen Zhebo,Lin Bin,Cao Xiangqun

DOI: https://doi.org/10.3788/cjl201946.1004003

2019-01-01

Abstract:Defocusing dither optimization techniques can eliminate the nonlinear error and overcome the limitation of refresh rate of a projector. However, the dithering algorithm is only a simple matrix transform and the dithering fringe after defocusing does not approximate the ideal sinusoidal fringe enough, inducing a measurement phase error. This paper proposes a binary particle swarm optimization (BPSO) method, and the binary defocusing dither technique is optimized. To speed up the BPSO process, binary patches arc first optimized; then, the patches arc joined together with respect to symmetry and periodicity to generate the full-size pattern. The simulation and experimental results demonstrate that the proposed method can obtain high quality measurement results under various extents of defocusing.
A new on-chip jitter measurement method based on cumulative distribution function

Jian Guo,Jianhua Feng,Hongfei Ye

2012-01-01

Abstract:The authors present a new on-chip jitter measurement method based on cumulative distribution function (CDF) to solve the problem of the mismatch of the delay line, taking up too much chip area and limited by high frequency oscillator signal, which are encountered in measuring multi-GHz clock jitter. The complete circuit is designed and implemented based on the 65 nm CMOS process. The simulation results show that the circuit is able to operate at 2.5 GHz and achieves a timing resolution up to 1 ps. © 2012 Peking University.
Effect on Pseudo Code Ranging Precision by A/D Sampling Clock Jitter

YU Fa-xin,XU Xiao-lin,GUAN Jie,ZHENG Yang-ming,JIN Zhong-he

DOI: https://doi.org/10.3969/j.issn.1004-1699.2007.05.030

2007-01-01

Abstract:Digital Signal Processing(DSP)technology is widely used in pseudo code ranging system of pico-satellite.With the limitation of small volume and low power consumption of pico-satellite,poor performance oscillator and simple circuit result in severe A/D sampling clock jitter and worsen pseudo code ranging precision.The noise model of A/D sampling clock jitter is analyzed in the pseudo code ranging DSP,which will have an effect on the tracking performance of Code Tracking Loop(CTL)in pseudo code regeneration.And,the simulation indicates that the interaction between clock jitter,sampling bits and intermediate frequency will influence ranging precision.
Monitoring Method of Micro Flying Head Jitter in Optical Storage

Zhen Huan Wu,Yu He Li,Kai Sen Guan,Xin Qi

2015-01-01

Abstract:Storage technology plays an important role in information field. With the increase of storage density, the flying height is up to nano-scale. A kind of measuring principle of jitter for micro flying head was introduced. The piezoelectric bimorph was used for vibration suppression. Based on DirectX technology, a virtual reality environment was developed to monitor the working condition of flying head to ensure the performance of optical storage system. Achieve jitter attenuation of flying head slider between head and disk, through the experiment of the disc loading process and the smooth condition. Finally, display with the virtual detecting environment.
Novel frame SYNC signal detection method for multi-level optical discs

MingMing Yan,PEI Jing,YANG Bo,Longfa Pan

2009-01-01

Abstract:In the paper,a novel frame SYNC signal detection method for the multi-level optical disc is addressed.The method adopts the differentiation of the RF signal to obtain the time information of record marks,and the digital detection system for the frame SYNC signal is implemented on the FPGA chip.The method is independent with the threshold level,so it avoids the mistake detection caused by the fluctuation of the threshold level.The experimental result shows that the method can accurately detect the frame SYNC signal with the fallout ratio less than 1×10-4 and meets the needs of the multi-level optical disc.
A statistical jitter tolerance estimation applied for clock and data recovery using oversampling

Jing Yin,Lieguang Zeng

DOI: https://doi.org/10.1109/TENCON.2006.344147

2007-01-01

Abstract:In this article, an oversampling clock and data recovery unit (CDR) is introduced. Compared to the traditional PLL CDR, its intrinsic fast tracking performance makes it useful in burst model receiver. A jitter tolerance estimation based on ideal phase detection is introduced to assist systems analysis and performance parameters selection. The statistical simulation methodology enables much quicker verification of the bit error rate (BER) than direct BER measurement based on counting. The simulation results demonstrate the estimated jitter tolerance of the designed 155.52Mb/s oversampling CDR with proper parameters well exceeds the jitter tolerance specified for STM-1 level of synchronous optical network (SDH).
A Jitter Measurement Circuit Based On Dual Resolution Vernier Oscillator

Wei Tang,Jianhua Feng,Chunglen Lee

DOI: https://doi.org/10.1109/ASICON.2009.5351194

2009-01-01

Abstract:This paper presents a new on-chip jitter measurement circuit based on a dual vernier oscillator (VO) structure. The new structure measures the jitter with a low resolution VO first and then with a high resolution VO, thus greatly expanding the measurement range of the jitter and reducing the test time. The oscillators are implemented with differential digital controlled delay elements, whose oscillation periods can be precisely controlled The circuit has been implemented and verified with the SMIC 0.18 mu m technology and has been shown to have the ability of measuring jitters in the pico-second range.
A New Multilevel Interpolated TDC Method Based on a Two-Step Synchronizer

Dahe Liu,Xueyou Shi,Guangyi Chen,Wengao Lu,Zhongiian Chen

DOI: https://doi.org/10.1109/edssc.2019.8754482

2019-01-01

Abstract:A new multi-level time-to-digital converter (TDC) method capable of reaching high linearity and long dynamic range is presented in this paper. The method is based on a coarse counter and a two-level interpolator with a two-step synchronizer. This method solves the misalignment problem and guarantees synchronized and compatible total results. The synchronizer avoids the meta stability problem. With simulated 45% reduced minimum unit delay, the compensating delay line is shortened in coarse residue restoration. This work could be easily assembled in a multi-channel TDC chip and is aimed for applications such as APD based 3-D ranging.
Fully on-chip clock jitter and skew measurement scheme via incoherent subsampling

Yinxuan Lyu,Jianhua Feng,Kai Zhu,Hongfei Ye,Dunshan Yu

DOI: https://doi.org/10.1016/j.mejo.2019.104684

IF: 1.992

2020-01-01

Microelectronics Journal

Abstract:An incoherent subsampling scheme for on-chip measurement of high-speed clock jitter and skew is presented. A simple inverter-based ring oscillator with frequency selection multiplexers is used to generate uniform and un-correlated sampling events when binned in the unit period of the clock. The measurement results are directly reflected in the on-chip counters which are proportional to the injected jitter and skew. The measurement errors can be reduced with increasing sampling numbers. Theories of ring oscillator period suitability, sampling number requirement and jitter measurement are analyzed in detail. Behavioral simulations using MATLAB are performed to verify the proposed theories. The measurement circuit is implemented using a 55 nm CMOS process and the maximum measurement errors in skew mode and jitter mode from SPICE simulations are 0.121ps and 0.123 ps, respectively. The implemented measurement circuit has good immunity to PVT variations after proper tuning and the influence of supply noise is also investigated.
A Clock Calibration Method for an All-Digital Burst-Mode CDR with Embedded TDC

Baoguang Liu,Yuan Wang,Song Jia,Ganggang Zhang,Xing Zhang

DOI: https://doi.org/10.1109/edssc.2014.7061159

2014-01-01

Abstract:This paper presents a novel calibration method for an all-digital burst-mode clock and data recovery (BM-CDR) with embedded time-to-digital converter (TDC). The proposed method ensures the TDC-embedded Phase Generator to get the precise delays outside of Shared Delay Line, which makes the measured period more exactly. This method operates at 1.25Gbps. Compared with the BM-CDR without calibration, the proposed method reduces the clock jitter from 221.58ps to 98.11ps, about 55.72% under a 5-bit consecutive identical digits.
Counting Prognostication Technique and Results at 2.048 Mbit/s Desynchronizer Output for SDH Equipment

Qin Xiaoyi,Wang Hansheng,Zeng Lieguang

DOI: https://doi.org/10.1109/icct.1998.743129

1998-01-01

Abstract:Due to pointer adjustments, which play a primary role in phase noise accumulation, jitter and wander generation at the output of desynchronizer systems represents one of the most important topics in SDH (synchronous digital hierarchy) equipment. This paper describes a novel desynchronization technique-counting prognostication, to reduce the clock jitter of 2.048 Mbit/s signal in the SDH network. This technique is completely implemented by digital circuits and is apt to integrated. Moreover, analyses of jitter performance and experiment results are given to show that the recovered clock has very small jitter (about 0.04 UI) and has little jitter accumulation
Optimization of Modulation Code for a Multi-Layer Disc

赵辉,徐端颐,岳宏达

DOI: https://doi.org/10.3321/j.issn:1000-0054.2002.11.011

2002-01-01

Abstract:The current modulation code for a multilayer parallelaccess disc was optimized to increase the storage density. Two problems which affect the optimization are the acceptable jitter and the phaselocked loop (PLL) synchronization process. A novel method is proposed for procuring the clock information for a multilayer disc, which satisfies the PLL requirements. The effectiveness of the method was proven using probability theory. The optimized PLL parameters for the multilayer disc are d=4 and k=1015 which improve the track density by 15%23%.
On-chip Clock Jitter Testing Circuit Based on Pulse-Shrinkage and Accumulation Register

FENG WeiLei,FENG JianHua,YE HongFei,ZHANG Xing

DOI: https://doi.org/10.1360/n112014-00147

2014-01-01

Scientia Sinica Informationis

Abstract:An on-chip clock jitter testing circuit based on pulse-shrinkage TDC and accumulation register is introduced in this paper, which can be used to monitor the jitter of internal clock signal with sub-gate delay resolution. The whole testing circuit is consisted of pulse-shrinkage loop, accumulation register, XOR array, counter and control circuit. All the pulse-shrinkage units are connected in a loop to reduce the required number, so that the area can be saved and the effects of process variations can be reduced. Multi-cycle clock pulse measurement results are accumulated simultaneously and output in the form of serial code in monitor-mode, the clock jitter can be read directly from the serial code. The whole circuit is designed in a 65-nm CMOS process, simulation results show that the circuit can measure several GHz clock signal, with a resolution of 1 ps.
A simple interpolation algorithm for measuring multi-frequency signal based on DFT

Jing Wu,Wei Zhao

DOI: https://doi.org/10.1016/j.measurement.2008.06.008

IF: 5.6

2009-01-01

Measurement

Abstract:For the multi-frequency signal under the condition of asynchronous sampling, the spectral leakages such as the negative frequency leakage, long-range leakage and short-range leakage in Fourier transform will influence the accuracy of harmonic analysis. To reduce the measurement errors caused by these effects, a new interpolated discrete Fourier transform (DFT) algorithm using three greatest spectral lines is presented. In this new algorithm, the analytical formulas for the harmonic frequency are obtained by applying the Chebyshev best approximation theory. These formulas can be easily implemented by hardware multipliers, which is convenient for real-time measurement. The simulation and experiment results show the presented algorithm has high accuracy and good anti-jamming capacity.

Jitter Measurement Method for Multi-level Disc Based on Interpolation Algorithm

Jitter Measurement Method for Multi-Level Disc Based on Quadratic Interpolation Algorithm

Design on Measurement System for Jitter of High-speed Optical Disc

Jitter testing technology of high-speed optical disc

Analysis And Study On Measurement Of Jitter And Its Precision

Counter-Set Based PCR Jitter Correction Method for DVB-T System

Threshold-optimized Dithering Technique for High-quality 3D Shape Measurement

High-Quality Three-Dimensional Shape Measurement Based on Binary Particle Swarm Dithering Optimization

A new on-chip jitter measurement method based on cumulative distribution function

Effect on Pseudo Code Ranging Precision by A/D Sampling Clock Jitter

Monitoring Method of Micro Flying Head Jitter in Optical Storage

Novel frame SYNC signal detection method for multi-level optical discs

A statistical jitter tolerance estimation applied for clock and data recovery using oversampling

A Jitter Measurement Circuit Based On Dual Resolution Vernier Oscillator

A New Multilevel Interpolated TDC Method Based on a Two-Step Synchronizer

Fully on-chip clock jitter and skew measurement scheme via incoherent subsampling

A Clock Calibration Method for an All-Digital Burst-Mode CDR with Embedded TDC

Counting Prognostication Technique and Results at 2.048 Mbit/s Desynchronizer Output for SDH Equipment

Optimization of Modulation Code for a Multi-Layer Disc

On-chip Clock Jitter Testing Circuit Based on Pulse-Shrinkage and Accumulation Register

A simple interpolation algorithm for measuring multi-frequency signal based on DFT