Abstract:Fabricating chalcopyrite Cu(In,Ga)Se2 (CIGS) films from electrodeposition is one of the most effective ways to lower the production cost and energy consumption compared with that from vacuum methods. However, this process often produces a pronounced rough surface with impurity phases, induces the accumulation of gallium, and results in a low surface band gap. In this work, ammonium sulfide ((NH4)2S, AS) solution treatment is used as a single way to realize the optimization of the distribution of elements on the CIGS surface. It is revealed that this room-temperature process not only significantly reduces the surface roughness (Ra) but also incorporates sulfur (S) into the CIGS film successfully. An appropriate AS treatment duration can effectively remove the impurity phases and reduce the series resistance, and thus the dominant recombination moves from the CdS/CIGS heterojunction interface to the bulk. Consequently, the open-circuit voltage (VOC) and fill factor (FF) of solar cells have been greatly improved (from 484 to 532 mV, from 62.52 to 68.15%), leading to higher efficiency of 11.92%. This work focuses on revealing the etching mechanism of the CIGS films by the AS treatment at room temperature.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00220?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00220</a>.Best solar cell parameters of different unannealing samples (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00220/suppl_file/ae1c00220_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Influences of Plasma Activation Se Source on Selenization of Electrodeposited Cu-In-Ga Metallic Precursors

Preparation And Characterization Of Cu(In,Ga)Se-2 Thin Films By Selenization Of Cu0.8ga0.2 And In2se3 Precursor Films

Pulse Selenization in Cu(In,Ga)Se 2 Solar Cells: A Promising Approach to Achieve High Efficiency by Electrodeposition

Synthesis and Characterization of CIGS Powder

Metal Precursor Influence on Performance of Culn1−xGaxSe2 Films

Metal Precursor with Bi-Layer Indium for Cu(In,Ga)Se2 Thin Film Preparation

Growth and Characterization of Copper Indium Gallium Diselenide Films for Solar Cells Fabrication

Study on How the Content of Selenium in the Precursors Influences the Properties of CuInSe2 Thin Films

Metal Precursor Influence On Performance Of Cuin1-Xgaxse2 Films

Research progress on synthesis of CuIn1-x Gax Se2 nanoparticles

The Effects of Selenium Content on Cu(Inga)Se-2 Thin Film Solar Cells by Sputtering from Quaternary Target with Se-Free Post Annealing

Research progress on synthesis of CuIn 1-xGa xSe 2 nanoparticles

Influence of Ga Concent of CuInGa Precursor on Stoichiometry of Cu(In1 - xGax) Se2 Photon Absorption Films

Cu(In,Ga)Se2-based Solar Cells Prepared from Se-containing Precursors

Characterization of Cu(In,Ga)Se2 Films Deposited by Single-Step Electron Beam Evaporation for Solar Cell Applications

Optimization of Selenization Condition for Efficiency CIGSe Solar Cells Based on Postselenization of CuInGa Precursors

Growth of Zn doped Cu(In, Ga)Se 2 thin films by RF sputtering for solar cell applications

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature

Influences of Ga Concentration on Performances of CuInGaSe2 Cells Fabricated by Sputtering-Based Method with Ceramic Quaternary Target

A Review of Selenization of Metal Precursors for the Deposition of CIGS Thin Film

The Relationships Between Electronic Properties and Microstructure of Cu(In,Ga)Se-2 Films Prepared by Sputtering from A Quaternary Target