Abstract:In this study, Ni/nano-Al 2 O 3 composite coatings and the Ni/Ni–Al 2 O 3 multilayer coatings have been prepared on the 304 stainless steel substrate by adding the nano-Al 2 O 3 particle in Ni plating solution and by alternately brush electroplating, respectively. The microstructure, hardness and wear resistance of the composite and multilayer coatings were studied. Results showed that adding Al 2 O 3 nanoparticle in coatings significantly influences the size and growth direction of grain. The Al 2 O 3 content and hardness of coatings first increased, reached a maximum value of 603 HV and then decreased with the increase in the addition of Al 2 O 3 nanoparticle in Ni plating solution. The friction coefficient, wear loss and wear rate showed an opposite trend. In terms of mass loss and wear rate, the wear resistance of coating increases with increasing Al 2 O 3 content in coatings. An appropriate addition (20–25 g L −1 ) of Al 2 O 3 nanoparticles can effectively enhance the wear resistance of the brush electroplating Ni coating. The minimum wear rate is 2.2–2.3 10 −5 mm 3 N −1 m −1 . The multilayer structure coatings can prevent or delay microcrack initiation and growth by layer interface and grain boundary and increase the thickness of coatings without cracks. The multilayer coatings possessed the approximately same hardness (595 HV) and tribological properties compared with monolayer coatings.

Preparation, Microstructure and Tribological Properties of Nano-Al2o3/Ni Brush Plated Composite Coatings

Wear resistance of Ni/nano-Al2O3 composite coatings by brush electroplating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Composite Electroless Nickel-nano Al2O3 Coatings on Steel Substrate

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Wear Property of Nickel Matrix Nano-Al2O3 Electro-plating Composite Coating in Lubricated Condition Containing Solid Particles

Deposition Mechanism and Wear Resistance Nano Ni-Al2O3 Composite Coatings

Influence of solid contaminants in oil on wear characteristics of nano-Al2O3/Ni composite coating

EFFECT OF NANO-PARTICLE CONTENT ON TRIBOLOGICAL PROPERTIES OF ELECTRO-BRUSH PLATED COMPOSITE COATING IN OIL CONTAINING ABRASIVE CONTAMINANT

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Wear and Friction Properties of Electrodeposited Ni-Based Coatings Subject to Nano-enhanced Lubricant and Composite Coating

Microstructure, Mechanical and Tribological Properties of Plasma-Sprayed NiCrAlY-Mo-Ag Coatings from Conventional and Nanostructured Powders

Preparation and properties of Ni/P/single-walled carbon nanotubes composite coatings by means of electroless plating

Deposition Mechanism and Wear Resistance Nano Ni-Al<sub>2</sub>O<sub>3</sub> Composite Coatings

Nanostructured Ni–WC–Co composite coatings fabricated by electrophoretic deposition

Study on the Anti-wear Behavior of Ni-Co/Diamond Nanocomposite Coatings

Microstructure of Nanometer-sized Al2O3 Composite Coating Prepared by Electroless Plating

Investigation on Microstructure and Tribological Performances of Electrodeposited Ni-W-Y2O3 Composite Coatings

Technology for Ni-Al2O3 Composite Coating and Its Properties

Microstructure, mechanical properties and tribological behaviors of TiAlN-Ag composite coatings by pulsed magnetron sputtering method

Preparation and Tribological Behavior of Electrodeposited Ni–W–GO Composite Coatings