Abstract:This study successfully prepared crack-free WC10%-Ni60AA cermet coatings with high hardness using directed-energy deposition incorporating substrate preheating up to 500 °C. At the bottom of the deposit, the crack-free coating microstructure exhibited a lamination layer with a coarse herringbone eutectic, and the crystal-microstructure phase mainly comprised γ-Ni solid solution and eutectic precipitation Ni 17 W 3 , Ni 31 Si 12 , and Cr 23 C 6 . At the middle and top of the deposit, the microstructure exhibited a dense net-like eutectic, including a dendritic with the main phase of γ-Ni solid solution, interdendritic with a main phase of Cr 23 C 6 , and subdendritic with a main phase of Ni 31 Si 12 , Ni 17 W 3 , and a small block-like precipitate with a main phase of Cr 2.4 W 0.6 Si. Furthermore, the deposits on the substrate preheated to 500 °C exhibited the highest hardness (812 HV, an increase of 64 % compared to that of the non-preheating sample) owing to the dense net-like eutectic precipitation with fine-grain structure. Furthermore, wear test results show that the wearing process is divided into three stages: the rapid-increase stage; the plowing-friction stage; and the stable-wear stage. Specifically, as the load increased from 100 N to 400 N, the width and depth of the wear tracks increased, and the wear mechanisms were adhesive and oxidation, with the most severe wear occurring under a load of 400 N. Similarly, as the speed increased from 50 RPM to 300 RPM, the width and depth of the wear tracks increased, and the wear mechanisms were adhesive and oxidation at low speeds. When the speed was increased to 300 RPM, the most severe wear occurred, and the wear mechanisms were primarily adhesive and abrasive, along with a small amount of oxidation wear.

Nanostructured Ni–WC–Co composite coatings fabricated by electrophoretic deposition

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Electrodeposition of Ni-WC composite coatings: formation, structure and properties

Robust Ni/WC superhydrophobic surfaces by electrodeposition

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Microstructure and Wear Behavior of Hard Ni60 and Soft WC-12Co/Ni25 Coatings Prepared by Laser Cladding on W1813N Non-magnetic Stainless Steel

Microstructure and Wear Behavior of Hard Ni60 and Soft WC-12Co/N125 Coatings Prepared by Laser Cladding on W1813N Non-magnetic Stainless Steel

The Microstructure and Properties of Ni60/60% WC Wear-Resistant Coatings Prepared by Laser-Directed Energy Deposition

Study on the abrasive resistance of Ni-based coatings containing WC hard phase

Preparation and Tribological Behavior of Electrodeposited Ni–W–GO Composite Coatings

Microstructure and wear behaviors of a WC10%-Ni60AA cermet coating synthesized by laser-directed energy deposition

Preparation and Characterization of Pulse Electrodeposited Ni/W-SiC Nanocomposite Coating on Mild Steel Substrate

Preparation, Mechanical Properties and Wear Resistance of Ni–W/SiC Nanocomposite Coatings

Electrochemical Deposition and Nucleation/Growth Mechanism of Ni–Co–Y2O3 Multiple Coatings

Preparation and Properties of Ni–W Composite Coatings Reinforced by Graphene Nanoplatelets

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

Preparation and tribological properties of Ni-P electroless composite coating containing inorganic fullerene-like WS2 nanomaterials

Electrodeposition of Ni-P composite coatings: A review

Preparation and characterization of Ni-P-Al2O3-PTFE nanocomposite coatings by unidirectional jet electrodeposition

Microstructure and Properties of FeMnCrAl/Ni Coated WC Coatings Deposited by High Velocity Arc Spraying

A novel electrochemical deposited Fe Ni coating designed by laser-induced periodic current density: Effect of microstructure on microhardness and wear resistance improvement