Abstract:In this study, Ni/nano-Al 2 O 3 composite coatings and the Ni/Ni–Al 2 O 3 multilayer coatings have been prepared on the 304 stainless steel substrate by adding the nano-Al 2 O 3 particle in Ni plating solution and by alternately brush electroplating, respectively. The microstructure, hardness and wear resistance of the composite and multilayer coatings were studied. Results showed that adding Al 2 O 3 nanoparticle in coatings significantly influences the size and growth direction of grain. The Al 2 O 3 content and hardness of coatings first increased, reached a maximum value of 603 HV and then decreased with the increase in the addition of Al 2 O 3 nanoparticle in Ni plating solution. The friction coefficient, wear loss and wear rate showed an opposite trend. In terms of mass loss and wear rate, the wear resistance of coating increases with increasing Al 2 O 3 content in coatings. An appropriate addition (20–25 g L −1 ) of Al 2 O 3 nanoparticles can effectively enhance the wear resistance of the brush electroplating Ni coating. The minimum wear rate is 2.2–2.3 10 −5 mm 3 N −1 m −1 . The multilayer structure coatings can prevent or delay microcrack initiation and growth by layer interface and grain boundary and increase the thickness of coatings without cracks. The multilayer coatings possessed the approximately same hardness (595 HV) and tribological properties compared with monolayer coatings.

Microstructure of Nanometer-sized Al2O3 Composite Coating Prepared by Electroless Plating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation of NiAl2O4/Al2O3 composite nanopowder

Composite Electroless Nickel-nano Al2O3 Coatings on Steel Substrate

Co–Al2O3 nanocomposites powder prepared by electroless plating

Technology for Ni-Al2O3 Composite Coating and Its Properties

Wear resistance of Ni/nano-Al2O3 composite coatings by brush electroplating

Study on Ni-P-nanoTiN Electroless Composite Coating

Tailoring role of Al and Ti particles in the microstructure and property of electrodeposited Ni matrix nanocomposite coatings

Characterization of Ni coating layer of Al2O3 particles and their wettability behavior in Al2O3@Ni/Al-10Si composites

Effect of nano-Al 2 O 3 particle addition on Co–P–xAl 2 O 3 nanocomposite plating electroplated on X65 steel

Microstructure and mechanical properties of electroless Ni–P–Si 3 N 4 –TiN composite coatings

Study of Fe-Ni(Cr) Alloy and Nano-Al2o3 Particles Composite Coating Prepared by Laser Cladding

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Effect of Surface Roughness and Structure Features on Tribological Properties of Electrodeposited Nanocrystalline Ni and Ni/Al2O3 Coatings

Preparation of Fe Coating Al<sub>2</sub>O<sub>3</sub> Nanometer Composite Powder and its Mechanical Properties after Hot Press Sintering

Microstructure, Friction, And Wear Properties Of Ni-Al2o3-Mos2 Composite Coatings

Microstructure and properties of Cr-AlN composite coating prepared by pack-cementation on the surface of Al-containing ODS steel

Tribological performance and high temperature oxidation behaviour of thermal sprayed Ni- and NiCrAlY-based composite coatings

Deposition of NiAl/Al3Ni2(CrB2) Coatings from Ni, Al and CrB2 Powders Using Mechanical Synthesis in Planetary Ball Mill

The Preparation and Properties of Ni2Al3 Intermetallic Compound Coating