Abstract:TiAlSiN nanocomposite coatings were deposited in a closed field unbalanced magnetron sputtering system by reactive sputtering from Ti0.475Al0.475Si0.05 targets using modulated pulsed power magnetron sputtering (MPPMS) under a floating substrate bias. The ratio of the nitrogen flow rate to the total gas flow rate (fN2) was varied from 0 to 40%. The application of MPPMS as sputtering sources was aimed at generating a high ionization degree of the sputtered material and a high plasma density by using a pulsed high power approach. When fN2=0%, an amorphous-like structure Ti0.479Al0.454Si0.066 coating was deposited with a hardness of 10GPa. When nitrogen was added, an optimized nanocomposite structure of nc-TiAlN/a-Si3N4 formed in the TiAlSiN coating deposited at fN2=10%, in which 5–10nm TiAlN nanocrystallites were embedded in a 2–3nm thick amorphous Si3N4 matrix. As the fN2 was increased up to 40%, the elementary composition of the coatings remained almost the same, but the grain size of nanocrystallites approached to 10–20nm and the AlN phase gradually precipitated. A maximum hardness (H) of 33.2GPa, a hardness to the elastic modulus (E) ratio of 0.081 and an H3/E*2 ratio of 0.19GPa were found in the coating deposited at fN2=10%. The friction coefficient of the TiAlSiN coatings was around 0.8–0.9 as sliding against a Si3N4 counterpart under a normal load of 0.5N. A wear rate of 2.0×10−5mm3N−1m−1 was measured in the TiAlSiN coatings deposited at fN2=20–40%. As only a low residual stress is found in the TiAlSiN coatings, we consider the complete phase separation is responsible for the enhanced mechanical and tribological properties of the nc-TiAlN/a-Si3N4 nanocomposite coatings.

Microstructure and mechanical properties of electroless Ni–P–Si 3 N 4 –TiN composite coatings

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Study on Ni-P-nanoTiN Electroless Composite Coating

Preparation and Properties of Ni–Co–P/nano‐sized Si3N4 Electroless Composite Coatings

Influence of multi-interfacial structure on mechanical and tribological properties of TiSiN/Ag multilayer coatings

Influence of Si Content on Microstructure and Mechanical Properties of TiAlSiN Nanocomposite Coatings

Microstructure and Properties of Ni-P Electroless Composite Coating Added with Nano-TiO2

Microstructure and Wear Resistance of Electrodeposited Ni-Sio2 Nano-Composite Coatings on Az91hp Magnesium Alloy Substrate

Microstructure and Wear Resistance of a Composite Coating Prepared by Laser Alloying with Ni-Coated Graphite on Ti-6Al-4V Alloy

Microstructure and Mechanical Properties of Ti Al Si N Nano-Composite Coatings Deposited by Ion Beam Assisted Deposition

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Enhanced wear resistance of Ni-Mo-TiN composite coating by synergistic effect of tough Ni-Mo matrix and hard TiN particles

Electrodeposition and corrosion resistance of Ni–P–TiN composite coating on AZ91D magnesium alloy

Microstructure, Mechanical Properties, and Oxidation Resistance of Nanocomposite Ti–Si–N Coatings

Effect of Microstructure on Mechanical and Tribological Properties of Tialsin Nanocomposite Coatings Deposited by Modulated Pulsed Power Magnetron Sputtering

Fabrication and Performance of Ni-Co-P/Si<sub>3</sub>N<sub>4</sub> Electroplated Composite Coatings on Al-Si Alloys

Microstructure and Performance of Laser Alloying Si3N4/Graphite Composite Coating

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

Microstructure, mechanical properties and tribological behaviors of TiAlN-Ag composite coatings by pulsed magnetron sputtering method

The Microstructure and Mechanical Properties of Ti-Si-N Nanocomposite Coating Prepared by DC Magnetron Sputtering

Microstructures and Mechanical Properties of Ni-coated SiC Particles Reinforced AZ61 Alloy Composites