Abstract:A range of Fe-Cr-Ni alloys are used in nuclear power plants due to their high mechanical strength and corrosion resistance. As a major component of these alloys, Ni contributes to the formation of austenite microstructures. In many nuclear reactor applications the alloys are exposed to ionizing radiation (g-rays) that can continuously decompose water to a range of highly redox active species (such as •OH, H2O2, O2). The change in water chemistry induced by radiation can affect both the general and localized corrosion behaviour of these alloys. In particular, its influence on the susceptibility of an alloy to localized corrosion such as crevice and stress corrosion cracking (SCC) are important for assessment of reactor component aging. As well, corrosion products that dissolve into the reactor coolant can be transported to the reactor core where they can be neutron activated. This can create a radiological hazard for reactor maintenance personnel. Thus, quantifying the rate of general corrosion and the corrosion product transport in a reactor are important safety, operation and maintenance issues. It has been well established that the type of oxide that forms on a surface is a critical factor in determining both general and localized corrosion behaviour. Both alloy composition and water chemistry affect the type of oxide that forms. Systematic studies that examine the effect of alloy composition on corrosion are rare and those available have been conducted mostly from a metallurgical perspective. There are even fewer studies that examine the combined effects of alloy composition and corrosion environment. A fundamental understanding of the mechanism by which the Fe to Ni ratio in a steel alloy influences the corrosion rate in different environments will provide valuable information that can be used for alloy selection and usage. We have investigated the effect of the Fe to Ni ratio of alloy on oxide formation and growth kinetics. For this study, customized steel alloys with different Ni contents and constant Cr content (18 ± 1 %) were prepared. The Ni content ranged from 15 to 25 wt.%, within the range between AISI 316L and Alloy 800 (Fig. 1). The corrosion kinetics was investigated using a combination of coupon corrosion tests and electrochemical measurements. These measurements were augmented by oxide surface and depth analyses using several spectroscopic and imaging techniques, and by post-test solution analyses for dissolved metal loss. We found that the oxide formed at pH 10.6 and 80 °C has a graded layer structure, consisting of a mixed spinel oxide (FeCr2O4/Fe3O4/NiFe2O4) as an inner layer and Ni(OH)2 as an outer layer. The increase in Ni content from 15 to 25 wt.% does not affect the inner layer but increases the thickness of the Ni(OH)2 layer. The increase in Ni content also decreases the total amount of dissolved metal loss. Gamma-irradiation of the corroding system increases the corrosion potential on these alloys. Correspondingly, gamma-radiation accelerates the formation of passive oxide layers and decreases the overall rate of metal dissolution. The observed kinetics of oxide growth and metal dissolution can be explained by the competition kinetics of oxide growth and dissolution for oxidized metals. Figure 1

Effect of Ni on Corrosion Fatigue Properties of Medium Carbon High Strength Spring Steel

Influence of Ni Addition on Corrosion Performance of Medium-temperature Filler Metal with Low Cu Content for Al Brazed Joints

Effect of Ti on corrosion resistance of new medium-carbon high strength spring steel

Effects of Cr and Ni on the microstructure and corrosion resistance of high-strength low alloy steel

Effect of Nickel Content on Mechanical Properties of 2200 MPa Grade Ultra-High Strength Steels

Effect of Tensile Deformation on Microstructure and Corrosion Resistance of High Nitrogen Austenitic Stainless Steels

Experimental Study on Fatigue Crack Growth and Residual Strength of Steel 30crmnsini2a under Mixed Corrosive Environments

Influence of Ni content on impact-abrasion wear resistance of medium-carbon low alloy cast steel

Understanding the Effect of Ni on Mechanical and Wear Properties of Low-Carbon Steel from a View-Point of Electron Work Function

Influence of Nitrogen Content on the Corrosion Behavior of Powder Metallurgy Nickel-Free Austenitic Stainless Steel

Ultra high cycle fatigue behavior of a medium-carbon high strength spring steel NHS1

Improvement of Stress Corrosion Cracking Resistance by Low Cycle Fatigue of a CrNiMoV Steel

The Effect of W and Cu on the Microstructure and Properties of Ni-saving 25cr Duplex Stainless Steels

Effect of Nickel Content on the Corrosion Behaviour of Stainless Steel at 80 °C

Effect of Ni on the Ion-Selectivity of Rust Layer on Low Alloy Steel

The influence of Ni on the microstructure and corrosion resistance of high-strength low alloy steel in the Cl-containing environment

Fatigue fracture behaviour of a medium-carbon 2 000 MPa level high strength spring steel

Bending fatigue crack initiation and propagation behaviors of a nickel free high nitrogen stainless steel

Effect of Ni content on microstructure and mechanical properties evolutions of 9Cr high Si heat resistant steel deposited metals

Effect of Load Ratio and Saltwater Corrosive Environment on the Initiation Life of Fatigue of 10ni5crmov Steel

Effects of Ni on Austenite Stability and Fracture Toughness in High Co-Ni Secondary Hardening Steel