Abstract:In recent years, the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al-Si alloys. However, the effect of Ni on the wear behaviors of Al-Si alloys and Al matrix composites, particularly at elevated temperatures, remains an understudied area. In this study, Al-Si-Cu-Mg-Ni/20wt% SiC particles (SiCp) composites with varying Ni contents were prepared by using a semisolid stir casting method. The effect of Ni content on the dry sliding wear behavior of the prepared composites was investigated through sliding tests at 25 and 350°C. Results indicated that the θ-Al 2 Cu phase gradually diminished and eventually disappeared as the Ni content increased from 0wt% to 3wt%. This change was accompanied by the formation and increase in δ-Al 3 CuNi and ε-Al 3 Ni phases in microstructures. The hardness and ultimate tensile strength of the as-cast composites improved, and the wear rates of the composites decreased from 5.29 × 10 −4 to 1.94 × 10 −4 mm 3 /(N·m) at 25°C and from 20.2 × 10 −4 to 7 × 10 −4 mm 3 /(N·m) at 350°C with the increase in Ni content from 0wt% to 2wt%. The enhancement in performance was due to the presence of strengthening network structures and additional Ni-containing phases in the composites. However, the wear rate of the 3Ni composite was approximately two times higher than that of the 2Ni composite due to the fracture and debonding of the ε-Al 3 Ni phase. Abrasive wear, delamination wear, and oxidation wear were the predominant wear mechanisms of the investigated composites at 25°C, whereas delamination wear and oxidation wear were dominant during sliding at 350°C.

Influence of Ni content on impact-abrasion wear resistance of medium-carbon low alloy cast steel

Effects of Ni content and tempering temperatures on microstructure and properties of medium-carbon cast steel

The Influence of Ni Content on the Microstructure and Impact Wear Resistance Performance of High-Chromium Casting Infiltration Coating

Effect of Ni Content on Microstructure, Mechanical Properties, and Abrasion Behavior of Fe-B-C Alloy

Effects of Ni content on microstructure and wear behavior of Al–13Si–3Cu–1Mg-xNi-0.6Fe-0.6Mn alloys

Influence of Tungsten on Microstructure and Properties of As-Cast Hi-Cr Cast Iron

Effect of Carbon Content on Three-body Abrasive Wear Characteristics of 28Cr-3Ni Cast Alloys

Investigation on Microstructure and Properties of Low‐Carbon Wear‐Resistant Steels with Addition of Cr and Ni

Influences of Partial Substitution of C by N on the Microstructure and Mechanical Properties of 9cr18mo Martensitic Stainless Steel

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Effect of hardenability on microstructure and property of low alloy abrasion-resistant steel

The Effect of N Content on the Microstructure and Wear Resistance of Improved High-Carbon Chromium Bearing Steel

Microstructure and properties of hypereutectic high chromium cast iron containing nitrogen

A study of the abrasive wear of carbon steels

Effect of Nickel Content on Mechanical Properties of 2200 MPa Grade Ultra-High Strength Steels

Microstructure, Mechanical Properties and Wear Resistance of Low Alloy Abrasion Resistant Martensitic Steel Reinforced with TiC Particles

Effect of Short-Term Low-Temperature Austempering on the Microstructure and Abrasive Wear of Medium-Carbon Low-Alloy Steel

Effect of Ni content on microstructure and mechanical properties evolutions of 9Cr high Si heat resistant steel deposited metals

Effect of microstructure on wear resistance during high temperature carburization heat treatment of heavy-duty gear steel

Influence of Niobium Content on the Mechanical Properties and Abrasion Wear Resistance of Heat-Treated High-Chromium Cast Iron

Niobium‐Carbide‐Enhanced Wear Performance of High‐Carbon Steels