Abstract:Proton-conducting ceramic cells are promising devices for high-efficient energy conversion, while the preparation of defect-free electrolyte membranes is difficult and blocks their quick development. Here, a vacuum-assistant dip-coating method is developed to prepare defect-free BaCe0.4Zr0.4Y0.1Yb0.1O3-δ (BCZYYb4411) proton-conducting electrolyte membranes on porous anode (40 wt%BCZYYb4411 - 60 wt%NiO) substrates. Unlike the conventional dip-coating process, by using the vacuum-assistant dip-coating method, defects (like running through pinholes, cracks) that would cause gas leakage, short-circuit and low open-circuit voltage (OCV) in following electrochemical tests can be eliminated. By tuning the mass concentration of electrolyte powders in the coating slurry, thin electrolyte membranes with different thicknesses can be reproducibly prepared. Proton-conducting fuel cells (PCFCs) with BaCo0.4Fe0.4Zr0.1Y0.1O3-δ (BCFZY0.1) cathode show high OCV values closing to the theoretical value of 1.13 V at 600 °C, demonstrating that dense and defect-free electrolyte membranes are fabricated. The as-prepared PCFC with a 10-μm-thickness defect-free electrolyte membrane shows a high peak power density reaching up to 761 mW cm−2 at 650 °C and stability of more than 250 h at the current density of 200 mA cm−2 at 600 °C. All these results illustrate that the developed method is feasible to prepare dense and thin electrolyte membranes without defects for proton-conducting ceramic cells.

A modified suspension spray combined with particle gradation method for preparation of protonic ceramic membrane fuel cells

A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells

Stable, easily sintered BaCe0.5Zr0.3Y0.16Zn0.04O3−δ electrolyte-based protonic ceramic membrane fuel cells with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

An ammonia fuelled SOFC with a BaCe0.9Nd0.1O3-δ thin electrolyte prepared with a suspension spray

A Performance Study of Solid Oxide Fuel Cells with BaZr0.1Ce0.7Y0.2O3–δ Electrolyte Developed by Spray‐Modified Pressing Method

Direct ammonia proton-conducting solid oxide fuel cells prepared by a modified suspension spray

Fabrication and performance of a proton-conducting solid oxide fuel cell based on a thin BaZr0.8Y0.2O3-δ electrolyte membrane

Stable, Easily Sintered BaCe0.5Zr0.3Y0.16Zn0.04O3−δ Electrolyte-Based Proton-Conducting Solid Oxide Fuel Cells by Gel-Casting and Suspension Spray

In Situ Screen-Printed BaZr0.1Ce0.7Y0.2O3−δ Electrolyte-Based Protonic Ceramic Membrane Fuel Cells with Layered SmBaCo2O5+x Cathode

Repeatable preparation of defect-free electrolyte membranes for proton-conducting fuel cells

Screen-printed BaCe0.8Sm0.2O3-δ thin membrane solid oxide fuel cells with surface modification by spray coating

Prontonic ceramic membrane fuel cells with layered GdBaCo2O5+x cathode prepared by gel-casting and suspension spray

Low-temperature protonic ceramic membrane fuel cells (PCMFCs) with SrCo0.9Sb0.1O3-δ cubic perovskite cathode

Stable BaCe0.5Zr0.3Y0.16Zn0.04O3−δ Thin Membrane Prepared by in Situ Tape Casting for Proton-Conducting Solid Oxide Fuel Cells

Intermediate-to-low temperature protonic ceramic membrane fuel cells with Ba0.5Sr0.5Co0.8Fe0.2O3-δ–BaZr0.1Ce0.7Y0.2O3-δ composite cathode

A Novel Anode Supported BaCe0.7Ta0.1Y0.2O3−δ Electrolyte Membrane for Proton-Conducting Solid Oxide Fuel Cell

Stable proton-conducting Ca-doped LaNbO4 thin electrolyte-based protonic ceramic membrane fuel cells by in situ screen printing

Fabrication of BaZr0.1Ce0.7Y0.2O3 – Δ ‐based Proton‐Conducting Solid Oxide Fuel Cells Co‐Fired at 1,150 °C

Scalable Fabrication Process for New Structure BaZr0.8Y0.2O3-δ-based Protonic Ceramic Fuel Cells

Interfacial Modification for High-Efficient Reversible Protonic Ceramic Cell with a Spin-Coated BaZr0.1Ce0.7Y0.2O3-δ Electrolyte Thin Film

Thin Yttria-Stabilized Zirconia Electrolyte and Transition Layers Fabricated by Particle Suspension Spray