Abstract:Yttria-stabilized zirconia (YSZ) thin films on polycrystalline substrates were grown by cold-wall aerosol-assisted metallorganic chemical vapor deposition (MOCVD) at the temperatures of 673-1233 K using metal beta-diketonate chelates as precursors. Thin uniform films with amorphous structure were obtained below 673 K; when the deposition temperature increases to 773-1023 K, YSZ films appear to be a mixture of cubic and monoclinic phases; single cubic YSZ phase can be obtained at deposition temperature above 1023 K. The Y/Zr atom ratio estimated from the corresponding X-ray photoelectron spectroscopy peaks is less than the feed ratio, which can be interpreted by different transfer resistance of Y and Zr intermediates diffusing to the substrate surface. The films obtained at 673-1023 K possess a layer structure originated from low mobility of the absorbed species. Along with the increase of the deposition temperature, the grains become mature and larger, and then unite with each other to form a continuous columnar film. Mass transport dominates the growth process within lower temperatures, and homogeneous reaction will interrupt the growth at increasingly high temperatures. Growth rate expression with respect to temperature, pressure, gas flow rate, and metal concentration of precursor solutions was deduced assuming deposition of mass-transport limited mechanism, which is consistent with the experimental results. (c) 2005 The Electrochemical Society. All rights reserved.

Fabrication of YSZ Thin Films from Suspension by Electrostatic Spray Deposition

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Deposition of Y2O3 stabilized ZrO2 thin films from Zr(DPM)4 and Y(DPM)3 by aerosol-assisted MOCVD

Formation and Rate Processes of Y2o3 Stabilized Zro2 Thin Films from Zr(Dpm)(4) and Y(Dpm)(3) by Cold-Wall Aerosol-Assisted Mocvd

Formation and Rate Processes of Y[sub 2]o[sub 3] Stabilized ZrO[sub 2] Thin Films from Zr(DPM)[sub 4] and Y(DPM)[sub 3] by Cold-Wall Aerosol-Assisted MOCVD

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Preparation of Yttria-Stabilized Zirconia(ysz)films by an Electrophoretic Deposition Method

Deposition and Characterization of YSZ Thin Films by Aerosol-Assisted CVD

Electrophoretic deposition of YSZ thin-film electrolyte for SOFCs utilizing electrostatic-steric stabilized suspensions obtained via high energy ball milling

The Novel Combination of Electrostatic Powder Coating with Suspension Coating for Fabricating the Dense YSZ Thin Film on Porous Anode Substrate

Fabrication Of Y2o3-Stablized Zro2 Ultrathin Film By Newly Developed Component-Controllable Langmuir-Blodgett Method

Fabrication of Zirconia Coatings Using Electrophoretic Deposition and Reactive Sintering

The fabrication technique of YSZ electrolyte film

Preparation Of Y2o3-Stabilized Zro2 Thin Electrolyte Films From Langmuir-Blodgett Film Precursors By Means Of Surface Ions

Preparation of Yttria stabilized Zirconia (YSZ) film by electrophoretic deposition (EPD) method

Preparation of YSZ Electrolyte Film by Electrophoretic Deposition under Constant Voltage

In-situ Coagulation of Yttria-Stabilized Zirconia Suspension Via Dispersant Hydrolysis Using Sodium Tripolyphosphate

Synthesis of Yttria-Stabilized Zirconia Particles by Flame Spray Pyrolysis Method

Dense nanostructured YSZ coating prepared by low-pressure suspension plasma spraying: Atmosphere control and deposition mechanism

Deposition of Surface-Melted YSZ Particles by Flame Spraying

Dense YSZ electrolyte films prepared by modified electrostatic powder coating