Abstract:Understanding the sintering processes extensively is critical in fabricating a flat cell for solid oxide fuel cell stacks, but few have reported the sintering process and stress development during the constrained sintering of the electrolyte layer on anode substrate. In this study, we show that the green tape of half cell fabricated by co-tape casting cracks into several pieces when it is heated directly to 1400 degrees C of profile I, while it remains flat and complete when the green tape is sintered with additional pre-sintered profile at 1300 degrees C of profile II. The strain rate characteristics indicate that the difference of 2.43 x 10(-6) s(-1) between the electrolyte and the anode layer leads to the stress development in the directly sintered cell, while it reduces to 6.7 x 10(-8) s(-1) for the pre-sintered cell, which is only 3% of that without pre-sintering. The stress based on continuum model calculated results in the sintered cell demonstrates that the stress increases from 0 at about 1000 degrees C to 2.60 MPa at 1300 degrees C, and increased from 2.60 MPa to 6.54 MPa in temperature range of 1300-1400 degrees C. But it was lower than half of the stress for the pre-sintered cell according to profile II. The SEM images, together with a circuit voltage of 2.22 V for two cell stack, indicate that the electrolyte of the unit cell is dense. The power is 41.7 W, with a power density of 0.26 W cm(-2) at 1.4 V and 750 degrees C for a two tells stacks sintered according to profile II. The ASR of the two cells stack is 2.50 Omega cm(2). Copyright (c) 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Study on Co-Sintering of Hydrogen Electrode and Electrolyte Prepared by Tape Casting for Solid Oxide Electrolysis Cell

Preparation and Electrochemical Performance of Hydrogen Electrode and Electrolyte for SOEC by Tape Casting and Lamination

Microstructure and electrochemical characterization of solid oxide fuel cells fabricated by co-tape casting

Preparation And Co-Sintering Of Electrolyte And Hydrogen Electrode Via Tape Casting And Its Performances For Soec

Co-sintering anode and Y 2O 3 stabilized ZrO 2 thin electrolyte film for solid oxide fuel cell fabricated by co-tape casting

Preparation of Cu-CeO2-YSZ anode by tape casting and impregnation for solid oxide fuel cell

Co-Sintering of SDC / NiO-SDC Bi-Layers Prepared by Tape Casting

Electrochemical Characteristics and Sintering Preparation of MetalHydride Electrode for Air-MH Semi-fuel Cell Applications

Fabrication of anode supported solid oxide electrolysis cell with the co-tape casting technique and study on co-electrolysis characteristics

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Preparation of Ni/Ysz Anode Material Using Gel-Tape Casting and Performance Analysis

Co-electrolysis of H2O and CO2 in a solid oxide electrolysis cell with hierarchically structured porous electrodes

Constrained Sintering of Y2O3-stabilized ZrO2 Electrolyte on Anode Substrate

Slip Casting Combined with Colloidal Spray Coating in Fabrication of Tubular Anode-Supported Solid Oxide Fuel Cells

Fabrication and Characterization of Ni-SSZ/SSZ/LSM-SSZ Anode-Supported SOFCs by Tape Casting and Single-Step Co-Sintering Techniques

Ni/YSZ and Ni–CeO2/YSZ Anodes Prepared by Impregnation for Solid Oxide Fuel Cells

Optimization of the Solid Oxide Fuel Cell Anode by Tape Casting

Fabrication and evaluation of anode and thin Y2O3-stabilized ZrO2 film by co-tape casting and co-firing technique

Improvement of the Performances of Tubular Solid Oxide Fuel Cells by Optimizing Co-Sintering Temperature of the NiO/YSZ Anode-Ysz Electrolyte Double Layers

Optimization of Anode Structure for Intermediate Temperature Solid Oxide Fuel Cell Via Phase-Inversion Cotape Casting

Preparation and SEM of Ni/Ce-YSZ Anode Materials