Abstract:A co-tape casting technique was applied to fabricate electrolyte/anode for solid oxide fuel cells. YSZ and NiO–YSZ powders are raw materials for electrolyte and anode, respectively. Through adjusting the Polyvinyl Butyral (PVB) amount in slurry, the co-sintering temperature for electrolyte/anode could be dropped. After being co-sintered at 1400°C for 5h, the half-cells with dense electrolytes and large three phase boundaries were obtained. The improved unit cell exhibited a maximum power density of 589mWcm−2 at 800°C. At the voltage of 0.7V, the current densities of the cell reached 667mAcm−2. When the electrolyte and the anode were cast within one step and sintered together at 1250°C for 5h and the thickness of electrolyte was controlled exactly at 20μm, the open-circuit voltage (OCV) of the cell could reach 1.11V at 800°C and the maximum power densities were 739, 950 and 1222mWcm−2 at 750, 800 and 850°C, respectively, with H2 as the fuel under a flow rate of 50sccm and the cathode exposed to the stationary air. Under the voltage of 0.7V, the current densities of cell were 875, 1126 and 1501mAcm−2, respectively. These are attributed to the large anode three phase boundaries and uniform electrolyte obtained under the lower sintering temperature. The electrochemical characteristics of the cells were investigated and discussed.

Preparation And Co-Sintering Of Electrolyte And Hydrogen Electrode Via Tape Casting And Its Performances For Soec

Preparation and Electrochemical Performance of Hydrogen Electrode and Electrolyte for SOEC by Tape Casting and Lamination

Study on Co-Sintering of Hydrogen Electrode and Electrolyte Prepared by Tape Casting for Solid Oxide Electrolysis Cell

Preparation of Sr2FexMn1 xNbO6 delta YSZ/YSZ/Sr2FexMn1 xNbO6 delta YSZ Symmetric SOEC by Tape Casting and Its Performances

Fabrication of anode supported solid oxide electrolysis cell with the co-tape casting technique and study on co-electrolysis characteristics

Preparation and Performance of IT-SOFC with Anode-Supported Thin GDC Electrolytes by Tape Casting Process

Preparation of half-cell by bi-layer wet powder spraying and tape casting for anode-supported SOFCs

Preparation and Characterization of NiO/YSZ Cathode and BSCF/SDC Anode of SOEC for Hydrogen Production

Microstructure and electrochemical characterization of solid oxide fuel cells fabricated by co-tape casting

Preparation and Electrochemical Behavior of Dense Ysz Film for Soec

Fabrication and Characterization of Ssz Tape Cast Electrolyte-Supported Solid Oxide Fuel Cells

Preparation and SEM of Ni/Ce-YSZ Anode Materials

Fabrication of Electrode Supporters for Solid Oxide Fuel Cells by Tape Calendaring Process

Co-Sintering of SDC / NiO-SDC Bi-Layers Prepared by Tape Casting

Co-sintering anode and Y 2O 3 stabilized ZrO 2 thin electrolyte film for solid oxide fuel cell fabricated by co-tape casting

Tape Casting of Bilayered Anode Supports and Electrochemical Performance of SOFCs Based on Them

Performance Evaluation of Solid Oxide Fuel Cells with Thin Film Electrolyte Fabricated by Binder‐Assisted Slurry Casting

Preparation and Properties of Multi-Layer SOEC Composite Anodes

Fabrication and Characterization of Ni-SSZ/SSZ/LSM-SSZ Anode-Supported SOFCs by Tape Casting and Single-Step Co-Sintering Techniques

Preparation of Cu-CeO2-YSZ anode by tape casting and impregnation for solid oxide fuel cell

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing