Abstract:Hydrogen technologies and especially fuel cells, are promising alternatives to achieve a carbon-free energy and an ecofriendly transition [1] . The SOFC technology (Solid Oxide Fuel Cell) is an energy conversion system composed of a stack of a porous cathode, a dense electrolyte and a porous anode working at a temperature in the [600°C – 1000°C] range to obtain ionic conductivity above 10 -2 S/cm. Nowadays, tape-casting is typically used for mass and low-cost manufacturing of supporting half-cell (8YSZ electrolyte and Ni-YSZ anode) and the cathode layer is commonly deposited by screen-printing [2] . In line with the cost reduction problematic, this presentation will describe the development and optimization of a green sequential tape casting process to obtain the anodic half-cell and screen-printing for the cathode. To target green process, aqueous based slurries are used and only non-toxic organic components are selected. The amount of organic components, ceramic powder and water was optimized to obtain slurries with a shear-thinning behavior while managing the powder dispersion stability. The parameters of the drying heat treatment have been optimized based on Thermal Gravimetric Analysis leading to obtain a multilayer flexible green tape without any bubbles or cracks further annealed to eliminate the organics and co-sinter the stack under a porous YSZ load. The flat anodic half-cell with a thin and dense layer of 8YSZ on a thick and porous layer of NiO-YSZ is completed by screen-printing of La 2 NiO 4+ δ (cathode) based ink followed by a consolidation thermal treatment. The characterization using X-ray diffraction, scanning electron microscopy and operando electrochemical tests of the cell allow validating the efficiency of the sequential tape-casting to fabricate via environmentally friendly process and low cost SOFC. [1] Rissman, J. et al. (2020) 'Technologies and policies to decarbonize global industry: Review and assessment of mitigation drivers through 2070', Applied Energy, 266, p. 114848. doi:10.1016/j.apenergy.2020.114848. [2] Udomsilp, D. et al. (2021) 'Performance Benchmark of Planar Solid Oxide Cells Based on Material Development and Design.', Energy Technology, 9. doi:10.1002/ente.202001062.

Preparation of half-cell by bi-layer wet powder spraying and tape casting for anode-supported SOFCs

Fabrication and Characterization of Ni-SSZ/SSZ/LSM-SSZ Anode-Supported SOFCs by Tape Casting and Single-Step Co-Sintering Techniques

Preparation And Co-Sintering Of Electrolyte And Hydrogen Electrode Via Tape Casting And Its Performances For Soec

Planar SOFC fabricated by aqueous reverse sequential tape‐casting of the anode, electrolyte and barrier layer

Fabrication of Electrode Supporters for Solid Oxide Fuel Cells by Tape Calendaring Process

A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Co-Sintering of SDC / NiO-SDC Bi-Layers Prepared by Tape Casting

Co-sintering anode and Y 2O 3 stabilized ZrO 2 thin electrolyte film for solid oxide fuel cell fabricated by co-tape casting

Planar Anode Supported SOFC Fabricated By Sequential Aqueous Tape Casting, Constrained Cosintering and Screen-Printing

Preparation of anode supported thin electrolytes for IT-SOFCS

Tape Casting of Bilayered Anode Supports and Electrochemical Performance of SOFCs Based on Them

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Development of a Ni/Al 2 O 3 Cermet-Supported Tubular Solid Oxide Fuel Cell Assembled with Different Functional Layers by Atmospheric Plasma-Spraying

Slip Casting Combined with Colloidal Spray Coating in Fabrication of Tubular Anode-Supported Solid Oxide Fuel Cells

Improvement of Anode-Supported Solid Oxide Fuel Cells

Novel Approaches to Prepare the High Performance Dense Electolyte and Interconnect Applicable to SOFC by Atmospheric Plasma Spraying

Preparation of SOFC Cathode by Combining Electrostatic Spray and Infiltration Technique

Preparation and Performance of IT-SOFC with Anode-Supported Thin GDC Electrolytes by Tape Casting Process

Characterization of Self-Sealed Metal Supported SOFCs with the Very Low Pressure Plasma Sprayed ScSZ Electrolyte

Facile one-step forming of NiO and yttrium-stabilized zirconia composite anodes with straight open pores for planar solid oxide fuel cell using phase-inversion tape casting method