Abstract:At present, the most common type of SOFC is anode-supported SOFC (AS-SOFC), in which the cell is mechanically supported by the thick fuel electrode layer. Recently, Metal-supported SOFCs (MS-SOFCs) have attracted attention because of their potential for low cost and high mechanical robustness. However, the fabrication process of MS-SOFCs has not been established. The mechanical behavior of the cells under high temperature operation has not been clarified. In this study, we fabricated prototype MS-SOFCs using the plasma spray method. The cell was tested by electrochemical measurements, residual stress measurements, and SEM/EDX to clarify the mechanical behavior of MS-SOFCs under high temperature operation. The layers of anode (NiO-YSZ), electrolyte (LSGM9182), and cathode (LSCF6428) were formed on a metal substrate (SUS430) by atmospheric pressure plasma spraying (APS) to fabricate a single cell of MS-SOFC. Open circuit voltage, AC impedance, and I-V measurements were performed at 600°C, 650°C, and 700°C. The residual stress of LSGM9182 electrolyte was evaluated by cosα method [1] under the cell operation condition using specially designed chamber. The MS-SOFC with thicker electrode layers showed the much lower OCV than that of theoretical. In addition, the electrolyte had vertical cracks between cathode and anode after the 2nd thermal cycle. However the MS-SOFC with thinner electrode layers showed the higher OCV, which was nearly theoretical value, and much better I-V characteristics than the cell with thicker electrodes. Electrochemical impedance measurement revealed the plasma sprayed electrodes showed acceptable performance even though its microstructure was not optimized. The residual stress of LSGM electrolyte in the cell did not change so much during the cell operation. This might be caused by existence of small cracks in the electrolyte layer. This research was financially supported by NEDO. [1] K.Tanaka, Journal of the Society of Materials Science,japan,vol.66,No.7 (2017) 479-487

Fabrication and performance of atmospheric plasma sprayed solid oxide fuel cells with liquid antimony anodes

Cycling Characteristics of Tubular Liquid Antimony Anode Direct Carbon Fuel Cells Prepared by Atmospheric Plasma Spray

Influence of Atmospheric Plasma-Sprayed Composite Cathode on the Performance of Solid Oxide Fuel Cells

Development of Liquid Antimony Anode-Based Fuel Cells: Effects of Reaction-Induced Convection on Mass Transfer and Electrochemical Performance

Sulfur-Resistant Liquid Antimony Anode for Direct Carbon Fuel Cells

Study on Microstructure and Electrochemical Performance of Ni/YSZ Anode Deposited by APS

Performance of Tubular Solid Oxide Fuel Cell Assembled with Plasma-Sprayed Sc2O3–ZrO2 Electrolyte

Development of a Ni/Al 2 O 3 Cermet-Supported Tubular Solid Oxide Fuel Cell Assembled with Different Functional Layers by Atmospheric Plasma-Spraying

Plasma-spray Derived, Corrosion-Resistive Electrolyte for Liquid Antimony Anode Direct Carbon Fuel Cell

Fabrication of composite cathode by a new process for anode-supported tubular solid oxide fuel cells

Performance of Plasma-Sprayed Bi2O3–Er2O3–WO3 for Intermediate-Temperature Solid Oxide Fuel Cells (It-Sofcs)

Scandia-stabilized Zirconia Electrolyte with Improved Interlamellar Bonding by High-Velocity Plasma Spraying for High Performance Solid Oxide Fuel Cells

Novel Approaches to Prepare the High Performance Dense Electolyte and Interconnect Applicable to SOFC by Atmospheric Plasma Spraying

Performance of La0.8Sr0.2Ga0.8Mg0.2O3-based SOFCs with Atmospheric Plasma Sprayed La-doped CeO2 Buffer Layer

Numerical Simulation and Experimental Characterization of the Performance Evolution of A Liquid Antimony Anode Fuel Cell

Manufacture of Low-Temperature SOFC by APS Coating Technology

Introducing Anode Fluidization into a Tubular Liquid Antimony Anode Direct Carbon Fuel Cell

Electrochemical Performance and Mechanical Stress Evaluation of Metal-Supported Solid Oxide Fuel Cells Fabricated By Plasma Spray Method

Development of NiO-GDC Anode by Atmospheric Plasma Spraying for Metal-Supported SOFCs

Liquid Antimony Anode for Converting Sulfur-Containing Coal in Direct Carbon Fuel Cells

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell