Abstract:Hydrogen technologies and especially fuel cells, are promising alternatives to achieve a carbon-free energy and an ecofriendly transition [1] . The SOFC technology (Solid Oxide Fuel Cell) is an energy conversion system composed of a stack of a porous cathode, a dense electrolyte and a porous anode working at a temperature in the [600°C – 1000°C] range to obtain ionic conductivity above 10 -2 S/cm. Nowadays, tape-casting is typically used for mass and low-cost manufacturing of supporting half-cell (8YSZ electrolyte and Ni-YSZ anode) and the cathode layer is commonly deposited by screen-printing [2] . In line with the cost reduction problematic, this presentation will describe the development and optimization of a green sequential tape casting process to obtain the anodic half-cell and screen-printing for the cathode. To target green process, aqueous based slurries are used and only non-toxic organic components are selected. The amount of organic components, ceramic powder and water was optimized to obtain slurries with a shear-thinning behavior while managing the powder dispersion stability. The parameters of the drying heat treatment have been optimized based on Thermal Gravimetric Analysis leading to obtain a multilayer flexible green tape without any bubbles or cracks further annealed to eliminate the organics and co-sinter the stack under a porous YSZ load. The flat anodic half-cell with a thin and dense layer of 8YSZ on a thick and porous layer of NiO-YSZ is completed by screen-printing of La 2 NiO 4+ δ (cathode) based ink followed by a consolidation thermal treatment. The characterization using X-ray diffraction, scanning electron microscopy and operando electrochemical tests of the cell allow validating the efficiency of the sequential tape-casting to fabricate via environmentally friendly process and low cost SOFC. [1] Rissman, J. et al. (2020) 'Technologies and policies to decarbonize global industry: Review and assessment of mitigation drivers through 2070', Applied Energy, 266, p. 114848. doi:10.1016/j.apenergy.2020.114848. [2] Udomsilp, D. et al. (2021) 'Performance Benchmark of Planar Solid Oxide Cells Based on Material Development and Design.', Energy Technology, 9. doi:10.1002/ente.202001062.

Planar SOFC fabricated by aqueous reverse sequential tape‐casting of the anode, electrolyte and barrier layer

A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells

Planar Anode Supported SOFC Fabricated By Sequential Aqueous Tape Casting, Constrained Cosintering and Screen-Printing

An ammonia fuelled SOFC with a BaCe0.9Nd0.1O3-δ thin electrolyte prepared with a suspension spray

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

A high-performance planar anode-supported solid oxide fuel cell with hierarchical porous structure through slurry-based three-dimensional printing

Reversible fuel electrode supported solid oxide cells fabricated by aqueous multilayered tape casting

Scalable fabrication process of thin-film solid oxide fuel cells with an anode functional layer design and a sputtered electrolyte

Scalable and facile fabrication of tri-layer electrolytes by reactive sputtering for efficient and durable solid oxide fuel cells

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Fabrication of Electrode Supporters for Solid Oxide Fuel Cells by Tape Calendaring Process

Tape Casting of Bilayered Anode Supports and Electrochemical Performance of SOFCs Based on Them

Durability Study of Anode-Supported SOFC with Large-Area Fabricated By 4-Layer Sequential Co-Lamination and GDC Co-Firing Process

A Novel Co-firing Process for Multi-layers of Solid Oxide Fuel Cells

Fabrication and Characterisation of a Large-Area Solid Oxide Fuel Cell Based on Dual Tape Cast YSZ Electrode Skeleton Supported YSZ Electrolyte with Vanadate and Ferrite Perovskite-Impregnated Anode and Cathode

Facile preparation of electrodes of efficient electrolyte-supported solid oxide fuel cells using a direct assembly approach

Hierarchically oriented macroporous anode-supported solid oxide fuel cell with thin ceria electrolyte film.

Five‐layer reverse tape casting of IT‐SOFC

A High-Strength Solid Oxide Fuel Cell Supported by an Ordered Porous Cathode Membrane

A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray