Abstract:Hydrogen technologies and especially fuel cells, are promising alternatives to achieve a carbon-free energy and an ecofriendly transition [1] . The SOFC technology (Solid Oxide Fuel Cell) is an energy conversion system composed of a stack of a porous cathode, a dense electrolyte and a porous anode working at a temperature in the [600°C – 1000°C] range to obtain ionic conductivity above 10 -2 S/cm. Nowadays, tape-casting is typically used for mass and low-cost manufacturing of supporting half-cell (8YSZ electrolyte and Ni-YSZ anode) and the cathode layer is commonly deposited by screen-printing [2] . In line with the cost reduction problematic, this presentation will describe the development and optimization of a green sequential tape casting process to obtain the anodic half-cell and screen-printing for the cathode. To target green process, aqueous based slurries are used and only non-toxic organic components are selected. The amount of organic components, ceramic powder and water was optimized to obtain slurries with a shear-thinning behavior while managing the powder dispersion stability. The parameters of the drying heat treatment have been optimized based on Thermal Gravimetric Analysis leading to obtain a multilayer flexible green tape without any bubbles or cracks further annealed to eliminate the organics and co-sinter the stack under a porous YSZ load. The flat anodic half-cell with a thin and dense layer of 8YSZ on a thick and porous layer of NiO-YSZ is completed by screen-printing of La 2 NiO 4+ δ (cathode) based ink followed by a consolidation thermal treatment. The characterization using X-ray diffraction, scanning electron microscopy and operando electrochemical tests of the cell allow validating the efficiency of the sequential tape-casting to fabricate via environmentally friendly process and low cost SOFC. [1] Rissman, J. et al. (2020) 'Technologies and policies to decarbonize global industry: Review and assessment of mitigation drivers through 2070', Applied Energy, 266, p. 114848. doi:10.1016/j.apenergy.2020.114848. [2] Udomsilp, D. et al. (2021) 'Performance Benchmark of Planar Solid Oxide Cells Based on Material Development and Design.', Energy Technology, 9. doi:10.1002/ente.202001062.

A high-performance planar anode-supported solid oxide fuel cell with hierarchical porous structure through slurry-based three-dimensional printing

Facile preparation of patterned anode substrate for solid oxide fuel cells by direct-writing 3D printing technology

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Development of Highly Efficient and Durable Large-Area Solid Oxide Fuel Cell by a Direct-Ink-Writing Three-Dimensional Printer

A new and simple way to prepare monolithic solid oxide fuel cell stack by stereolithography 3D printing technology using 8 mol% yttria stabilized zirconia photocurable slurry

Vat Photopolymerization 3D Printing of NiO-YSZ Anode for Solid Oxide Fuel Cells

Planar SOFC fabricated by aqueous reverse sequential tape‐casting of the anode, electrolyte and barrier layer

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Solid Oxide Fuel Cells with 3D Inkjet Printing Modified LSM-YSZ Interface

Electrolyte-supported solid oxide fuel cells with ultra-thin honeycomb structure prepared by digital light processing 3D printing technology

Significance of advanced porous configurations in enhancing solid oxide fuel cell performance: a comparative analysis between conventional porous anodes and state-of-the-art variants

Fabrication and performance evaluation of planar solid oxide fuel cell with large active reaction area

Planar Anode Supported SOFC Fabricated By Sequential Aqueous Tape Casting, Constrained Cosintering and Screen-Printing

An Anode-Supported Solid Oxide Fuel Cell (SOFC) Half-Cell Fabricated by Hybrid 3D Inkjet Printing and Laser Treatment

Preparation and Properties of Direct-Methane Solid Oxide Fuel Cell Based on a Graded Cu-CeO<sub>2</sub>-Ni-YSZ Composite Anode

Optimization of Anode Structure for Intermediate Temperature Solid Oxide Fuel Cell Via Phase-Inversion Cotape Casting

Optimization of Cathode Structure for Anode Supported Planar Solid Oxide Fuel Cell

Fabrication of Particle-Stacking Porous Anode for Solid Oxide Fuel Cell Using Laser Powder Bed Fusion

Fabrication and Interfacial Structure of Ni-YSZ-LSM Porous Scaffold for Solid Oxide Fuel Cells

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Novel architectured metal-supported solid oxide fuel cells with Mo-doped SrFeO3−δ electrocatalysts